manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 267 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 267

PARKVIEW® REAR BACK UP CAMERA —
IF EQUIPPED

Your vehicle may be equipped with the ParkView® Rear
Back Up Camera that allows you to see an on-screen
image of the rear surroundings of your vehicle whenever
the shift lever is put into REVERSE. The image will be
displayed on the touchscreen display along with a cau-
tion note to “check entire surroundings” across the top of
the screen. After five seconds this note will disappear.
The ParkView® camera is located on the rear of the
vehicle above the rear License plate.

When the vehicle is shifted out of REVERSE, the rear
camera mode is exited and the navigation or audio screen
appears again.

When displayed, static grid lines will illustrate the width
of the vehicle and will show separate zones that will help
indicate the distance to the rear of the vehicle. The
following table shows the approximate distances for each
zone:

Zone

Distance to the rear of the vehicle

Red

0 - 1 ft (0 - 30 cm)

Yellow

1 ft - 3 ft (30 cm - 1 m)

Green

3 ft or greater (1 m or greater)

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

265

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments