Chrysler 200 Convertible 2014 User Manual Download Page 156

Page: 156 / 610

Send Messages Using Soft-Keys:

You can send messages using Uconnect® Phone. To send
a new message:

•

Touch the “Phone” soft-key,

•

Touch the “messaging” soft-key then “New Message,”

•

Touch one of the 18 preset messages and the person
you wish to send the message to,

•

If multiple numbers are available for the contact select
which number you would like to have the message
sent,

•

Press “Send” or “Cancel.”

154

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 200 Convertible 2014

Reviews:

Chrysler 200 Convertible 2014, User Manual, Page: 156 / 610

Search results

Summary of Contents for 200 Convertible 2014

Reviews: