manualshive.com logo in svg

Chrysler 200 Convertible 2014, User Manual, Page: 278 / 610

Share
Download
Chrysler 200 Convertible 2014 User Manual Download Page 278

It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage
door or gate motor.

1. Cycle the ignition to the ON/RUN position.

2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)

away from the HomeLink® button you wish to pro-
gram while keeping the HomeLink® indicator light in
view.

3. Continue to press and hold the HomeLink® button,

while you press and release (“cycle”), your hand-held
transmitter every two seconds until HomeLink® has
successfully accepted the frequency signal. The indi-
cator light will flash slowly and then rapidly when
fully trained.

4. Watch for the HomeLink® indicator to change flash

rates. When it changes, it is programmed. It may take
up to 30 seconds or longer in rare cases. The garage
door may open and close while you are programming.

5. Press and hold the programmed HomeLink® button

and observe the indicator light.

•

If the indicator light stays on constantly, program-
ming is complete and the garage door/device should
activate when the HomeLink® button is pressed.

•

To program the two remaining HomeLink® buttons,
repeat each step for each remaining button. DO NOT
erase the channels.

If you unplugged the garage door opener/device for
programming, plug it back in at this time.

276

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 200 Convertible 2014



































































































































































































































































































































































































































































































































































































































Reviews:

No comments