Champion D-H1TCM5 Installation/Operation Manual With Service Replacement Parts Download Page 19

Page: 19 / 75

Installation

1. Use a qualified detergent/chemical supplier for detergent/chemical and dispensing

equipment needs.

2. Labeled detergent control circuit connection terminals are provided in the control cabinet

for detergent and rinse agent dispensing equipment (supplied by others).

3. The illustration below shows the terminal board for the machine.

4. The signal connection points include:

• Detergent signal 120VAC, 1A max load.

• Rinse aid/Sanitizer signal 120VAC, 1A load.

• Vent Fan 120VAC, 1Amp max amp load

5. A 1/2" detergent probe injection point is

provided at the rear and left side of the

dishwasher.

6. Detergent may be added manually if the

dishwasher is not equipped with dispensing

equipment. Consult the chemical supplier for

recommended dosing amounts.

7. A 1/4" NPT rinse-aid injection point is provided

in the final rinse piping located at the top rear

of the dishwasher. Consult a chemical supplier

for the proper liquid rinse-aid.

COMMON

RINSE

DETERGENT

Chemical Connections

A chemical connection terminal board is provided to

supply chemical dispenser signal voltages.

1/4" NPT Rinse aid

Injection Point

Two detergent injection fittings are

provided in the wash tank.

A rinse-aid injection point is provided at

the top of the dishwasher.

Summary of Contents for D-H1TCM5












































































Search results

Summary of Contents for D-H1TCM5

Reviews:

Related manuals for D-H1TCM5

Brands by name

Popular brands

Champion D-H1TCM5, Installation/Operation Manual With Service Replacement Parts

Search results

Summary of Contents for D-H1TCM5

Reviews:

Related manuals for D-H1TCM5

Brands by name

Popular brands