Champion D-H1TCM5 Installation/Operation Manual With Service Replacement Parts Download Page 2

Page: 2 / 75

For future reference, record your dishwasher information in the box below.

Model Number__________________________ Serial Number_______________________

Voltage________________Hertz_____________ Phase__________________

Service Agent __________________________________ Tel:______________________

Parts Distributor _________________________________ Tel:______________________

ATTENTION:

The model no., serial no., voltage, Hz

and phase are needed to identify your

machine and to answer questions.

The machine data plate is located

on the front panel of the machine

Please have this information ready

if you call for service assistance.

National Service Department

In Canada:

In the USA:

Toll-free: 800/ 263-5798

Toll-free: 800/ 858-4477

Tel:

905/ 562-4195

Tel:

336/ 661-1556

Fax:

905/ 562-4618

Fax: 336/ 661-1660

email: [email protected]

The USGBC and the CaGBC Member Logos are trademarks owned by the U.S. Green Building Council and The Canadian Green

Building Council, respectively, and are used by permission. The logos signify only that Champion Industries and Moyer Diebel

are a USGBC member and a CaGBC member respectively. USGBC and CaGBC do not review, certify nor endorse the products

or services offered by its members.

Summary of Contents for D-H1TCM5












































































Search results

Summary of Contents for D-H1TCM5

Reviews:

Related manuals for D-H1TCM5

Brands by name

Popular brands

Champion D-H1TCM5, Installation/Operation Manual With Service Replacement Parts

Search results

Summary of Contents for D-H1TCM5

Reviews:

Related manuals for D-H1TCM5

Brands by name

Popular brands