Champion D-H1TCM5 Installation/Operation Manual With Service Replacement Parts Download Page 11

Page: 11 / 75

Installation

!!ATTENTION!!
Use caution

when moving or lifting the dishwasher to prevent damaging the dishwasher

or the installation site.

Check doorway and passageway clearance before moving the dishwasher.

Remove dishwasher front panel and check under the machine base for obstructions before moving.

1. Inspect the dishwasher for shipping damage

2. Check the dishwasher interior for curtains, panels and other supplies.

3. Lift the dishwasher off the shipping pallet and move the machine near its permanent location.

4. Leave a minimum of 5-1/2" between walls and the rear of the dishwasher.

5. Level the dishwasher side-to-side and front-to-back using a bubble level.

The dishwasher legs are adjusted by screwing them in or out.

6. Do not remove tags attached to the utility connections.

7. Remove the protective film from the dishwasher exterior.

8. Remove any foreign material from the dishwasher interior.

Receiving

5-1/2" [140mm]

Control

Cabinet

Front

5-1/2" [140mm] Min.

Control

Cabinet

DHBTC, DH1TC

Corner Configuration

DHBT, DH1T

Straight-through Configuration

Champion

WASH

POWER

WARNING!

TURN OFF POWER BEFORE

SERVICING MACHINE

RINSE PRESSURE

CYCLE

Remove two front panel screws

in preparation for utility connections

Summary of Contents for D-H1TCM5












































































Search results

Summary of Contents for D-H1TCM5

Reviews:

Related manuals for D-H1TCM5

Brands by name

Popular brands

Champion D-H1TCM5, Installation/Operation Manual With Service Replacement Parts

Search results

Summary of Contents for D-H1TCM5

Reviews:

Related manuals for D-H1TCM5

Brands by name

Popular brands