background image

ACCESSORIES

THE PROTECTOR SYSTEM

®

 PHOTOELECTRIC 

SENSORS

The photoelectric sensors are designed to detect an 

obstacle in the path of the electronic beam and stop the 

operator. Includes mounting brackets.
Model 50-220

ENTRAPMENT PROTECTION DEVICES

SENSING EDGE (2-WIRE, NON-MONITORED)

Sensing edges can detect an obstacle upon contact and 

stop the operator. 
Models G65MG0204, G65MG0205, G65MGR205, and 

G65MGS205

SENSING EDGE CHANNEL

Mounting channel for all MG020 type edges.
Model G65ME120C5

REMOTE ANTENNA EXTENSION KIT

The remote antenna extension kit allows the antenna 

to be remotely installed.
Model 86LM

Chamberlain offers a variety of LiftMaster Security

®

 and Passport

 remote 

controls to satisfy your application needs. Single-button to 4-button, visor or key 

chain. Additionally, Passport

 remote controls are ideal for integration with 

Telephone Entry and Access Control Systems. Contact your authorized LiftMaster 

dealer for details.

3-BUTTON SECURITY

®

 

REMOTE CONTROL

The 3-button remote control can be programmed to 

control the operator. Includes visor clip.
Model 373LM

3-BUTTON MINI-REMOTE CONTROL WITH 

SECURITY

®

The 3-button remote control can be programmed 

to control the operator. Includes key ring and 

fastening strip.
Model 370LM

WIRELESS ACCESS CONTROL RECEIVER

Access control receiver for up to 450 Security

®

 

remote controls.
Model STAR450-315

REMOTE CONTROLS

MISCELLANEOUS

MOUNTING STAND

For Model RSL Slide. Ideal to raise slide operator 

higher above the ground for snow and other 

applications.
Model MSLM

HEATER

Keeps operator gearbox and batteries at suitable 

temperature when outside temperature is below 0°F 

for extended periods of time.
Models HTRKITRSL (includes bracket for optimal 7AH 

battery location) and G6518SL (replacement 

heater only)

SOLAR PANEL KIT - 10 WATT

This kit is to replace or add a solar panel to the 

operator application. Up to three solar panels can be 

connected to the operator.
Model SOLPNL10W12V

VEHICLE SENSING PROBE

The vehicle sensing probe is buried in the ground and 

can detect a car as it approaches and will then open 

the gate.
Model LM202

BATTERY FOR GATE ACCESS SYSTEMS

The gate access system battery replaces or adds a 

battery to the operator application. 
Model 29-NP712 (7 AMP-Hour Battery, 12 Vdc)
Model A12330SGLPK (33 AMP-Hour Battery with 

Harness, 12 Vdc. Ideal for solar applications and 

extended battery backup)

LOOP DETECTOR

Low power loop detectors.
Model LD7LP

SECURITY

®

 

KEYLESS ENTRY

Enables homeowner to operate gate operator from 

outside by entering a 4-digit code on a specially 

designed keypad. 
Model 377LM

DUAL GATE WIRING KIT

The dual gate wiring kit is 40 feet of interconnecting 

cable required for dual gate applications.
Model MSWIRE12GA6C

SOLENOID GATE LOCK (LOW POWER)

The automatic gate lock is a solenoid-driven lock that 

automatically unlocks when the gate is open and locks 

when the gate is closed. Can be mounted onto a gate 

or post. Can be released in case of emergency.
Model SGLOCK12V

MAGNETIC GATE LOCK

Outdoor magnetic lock, transformer, junction box, 

mounting plate and hardware. Not for use with Solar 

Applications. Must be powered separately.
Model MG1300

RELAY KIT

Maglock/Solenoid Lock release relay.
Model Q400MAU

BATTERY HARNESS

Required when a second 7AH battery is installed.
Model K94-35225

30

Summary of Contents for Elite RSL12V

































Reviews: