Chamberlain Elite RSL12V Installation Manual Download

Page: 14 / 32

WIRING

» POWER CONNECT BATTERIES

CONNECT BATTERIES

The batteries are charged in the circuit by using the transformer (provided) or an

optional solar panel. Batteries will degrade over time depending on temperature and

usage. For best performance, the batteries should be replaced every 3 years.

Batteries do not perform well in extremely cold temperatures. The operator comes

with one 7AH battery. A second 7AH (29-NP712) battery may be added or one

33AH (A12330SGLPK) may be used in place of the 7AH batteries.

NOTE:

There may

not be sufficient mounting space for the 33AH battery if a heater is installed.

Always

disconnect the batteries BEFORE servicing the operator.

NOTE:

Setting the battery on concrete will not have a negative affect on the

charging or battery life.

If the installation is a dual gate, proceed to next page.

Locate the battery plug.

Connect the battery plug to either connector on the control board.

Battery

Plug

Connector

NOT AVAILABLE

POWER WIRING

SOLAR PANEL (NOT PROVIDED. SEE ACCESSORIES.)

The solar panel(s) must be located in an open area clear of obstructions

and shading for the entire day.

The gate operator is not supported in northern

climates where temperatures reach below -4˚F. This is due to cold weather and a

reduced number of hours of sunlight during the winter months. Cycle rate may vary

from solar chart for areas that reach below 32˚F. Solar panels should be cleaned on

a regular basis for best performance to ensure proper operation. For solar

applications, a minimum of 20W solar panels and two 7AH batteries are

recommended. For Zone 3 cold weather sites, one 33AH battery is recommended.

We recommend LiftMaster low power draw accessories to minimize power draw,

refer to accessory page.

Accessories Zone 1

Zone 2

Zone 3

(6 Hrs sunlight/day) (4 Hrs Sunlight/day) (2 Hrs Sunlight/day)

20W
SOLAR
PANEL

30W
SOLAR
PANEL

50 50 38 43 20

✔

48 50 32 36 17

✔

50 50 30 35 12

✔

41 49 21 26 3

✔

1 9 0 0 0

50 50 50 50 31

✔

50 50 48 50 26

✔

50 50 50 50 24

✔

50 50 41 50 15

✔

30 43 1 9 0

NUMBER OF CYCLES PER DAY

Single Gate Installations (16 ft. 650 lb. gate)

Solenoid

Lock

100

300

2 7AH

Batteries

(optional)

1 33AH

Battery

(optional)

2 7AH

Batteries

(optional)

1 33AH

Battery

(optional)

1 33AH

Battery

(optional)

25 29 17 19 9

✔

23 27 15 17 8

✔

22 26 13 15 5

✔

18 22 9 12 1

✔

0 4 0 0 0

39 45 25 29 14

✔

35 41 23 27 13

✔

35 41 22 26 10

✔

31 37 18 22 6

✔

13 19 0 4 0

Solenoid

Lock

100

300

2 7AH

Batteries

(optional)

1 33AH

Battery

(optional)

2 7AH

Batteries

(optional)

1 33AH

Battery

(optional)

1 33AH

Battery

(optional)

20W
SOLAR
PANEL

30W
SOLAR
PANEL

Dual Gate Installations (16 ft. 650 lb. gate)

Accessories Zone 1

Zone 2

Zone 3

(6 Hrs sunlight/day) (4 Hrs Sunlight/day) (2 Hrs Sunlight/day)

Provided

Optional

(not provided)

Accessories

Single Gate (16 ft. 650 lb. gate)

BATTERY
BACKUP
(BBU)

40 100 275

✔

36 83 228

✔

43 98 269

✔

42 97 267

✔

41 94 258

Solenoid

Lock

100

300

1 7AH

Battery

(standard)

2 7AH

Batteries

(optional)

1 33AH

Battery

(optional)

Accessories

Dual Gate (16 ft. 650 lb. gate)

BATTERY
BACKUP
(BBU)

19 44 121

✔

17 40 111

✔

19 44 121

✔

19 43 120

✔

19 43 118

Solenoid

Lock

100

300

1 7AH

Battery

(standard)

2 7AH

Batteries

(optional)

1 33AH

Battery

(optional)

NUMBER OF CYCLES FOR BATTERY BACKUP

Summary of Contents for Elite RSL12V

































Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands

Chamberlain Elite RSL12V, Installation Manual

Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands