background image

CONCRETE PAD AND OPERATOR ATTACHMENT

Check the national and local building codes before installation.

Install the electrical conduit.

Pour a concrete pad (reinforced concrete is recommended). The concrete pad 

should be 6 inches above the ground and deeper than the frost line.

Attach the operator to the concrete pad with appropriate fasteners.

NOTE: 

An alternative to a concrete pad is to post mount the operator 

(refer to accessories).

INSTALLATION

 » DETERMINE LOCATION FOR CONCRETE PAD AND OP CONCRETE PAD AND

 

 OPERATOR ATTACHMENT

DETERMINE LOCATION FOR CONCRETE PAD AND 

OPERATOR

The gate operator should be installed near the front roller of the gate or near 

the back of the gate (in the OPEN position). The space between the gate and 

the output sprocket must be a minimum of 4 inches.

Lay out the concrete pad.

4"(10 cm) 

24"

(61cm)

1

2
3

STANDARD INSTALLATION

REAR INSTALLATION

1

2

1

2

4"(10 cm) 

24"

(61cm)

24" (61cm)

24"

(61cm)

4 Concrete Anchors

1/2" x 3 1/2"

Below the frost line. 

Check all national and 

local codes.

6" Above Ground

1 3

2

24"

(61cm)

24"

(61cm)

13.65"

MOUNTING FOOTPRINT

7.49"

(Electrical 

Box)

.63"

1

2

10

Summary of Contents for Elite RSL12V

































Reviews: