Chamberlain Elite RSL12V Installation Manual Download

Page: 15 / 32

GATE 1

GATE 2

GATE 1

GATE 2

Terminal Block Connector

Red

Blue

Green

Brown

White
Yellow

Yellow

White

Extension Cable

WIRING

» PRIMARY / SECONDARY OPERATORS

PRIMARY/SECONDARY OPERATORS

NOTE:

Use the Dual Gate Wiring Kit. Refer to the accessory page for more

information.

Before digging, contact local underground utility locating companies. Choose one

operator to be the primary and the other operator to be the secondary.

The control board in the secondary operator is not used

Trench across driveway to bury the extension cable.
Disconnect the terminal block connector (with the attached label) from the end

of the extension cable. Thread the extension cable through the bottom of the

primary operator (using the watertight connectors) and reconnect the extension

cable wires to the terminal block connector.
Connect the terminal block (with the attached label) to the GATE 2 connector of

the primary operator's control board.
Disconnect the terminal block connector from the other end of the extension

cable. Thread the extension cable through the bottom of the secondary

operator (using the watertight connectors) and reconnect the wires to the

terminal block connector.
Disconnect the wires from the GATE 1 connector on the secondary operator and

connect them to the terminal block connector.
Move the battery from the secondary operator to the primary operator.

Connect the plugs from the batteries to the connectors on the control board.
Check to make sure the LOCK/BIPART DELAY switch is OFF on the primary

control board. Factory default setting is OFF.

Gate 2

Gate 1

PRIMARY OPERATOR

SECONDARY OPERATOR

Gate 1

SECONDARY

CONTROL BOARD

NOT USED

GATE 2

ACCESSORY

POWER

GATE 1

12 V

LOCK /

OFF

BIPART DELAY

Battery from secondary operator

Battery from primary operator

PRIMARY OPERATOR

Extension

Cable

Gate 1

Secondary

Operator

Label

Extension Cable

Summary of Contents for Elite RSL12V

































Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands

Chamberlain Elite RSL12V, Installation Manual

Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands