Chamberlain Elite RSL12V Installation Manual Download

Page: 20 / 32

Outside

oper

Inside

oper

Outside

oper

Inside

oper

Outside

oper

Inside

oper

GATE 2

SET

LIMIT

GATE 1

SET

LIMIT

GATE

SET

OPEN

LIMIT

LEARN
LIMITS

SET

DIAGNOSTIC

GATE 1

CLOS

DIAGNOSTIC

GATE 1

FORCE

GATE 2

SET

LIMIT

LE
LIMITS

FORCE

GATE 2

SET

LIMIT

LE
LIMITS

SET

OPEN

LIMIT

SET

LIMIT

SET

OPEN

LIMIT

SET

LIMIT

Outside

oper

Inside

oper

Outside

oper

Inside

oper

DUAL GATE (RIGHT-SIDE PRIMARY OPERATOR)

Close the gate.

Press and release the LEARN LIMITS button. The SET OPEN LIMIT LED will blink.

PROGRAM OPEN

Press and hold the GATE 1 left button to move the right operator to the desired

OPEN position. When the gate is in the desired position, release the button.

NOTE:

The GATE 1 right and left buttons can be used to jog the gate back and

forth as needed.

Press and hold the GATE 2 left button to move the left operator to the desired

OPEN position. When the gate is in the desired position, release the button.

NOTE:

The GATE 2 right and left buttons can be used to jog the gate back and

forth as needed.

Press and release the LEARN LIMITS button. The control board will beep and the

SET CLOSE LIMITS LED will blink.

PROGRAM CLOSE

Press and hold the GATE 2 right button to move the left operator to the desired

CLOSED position. When the gate is in the desired position, release the button.

NOTE:

The GATE 2 right and left buttons can be used to jog the gate back and

forth as needed.

Press and hold the GATE 1 right button to move the right operator to the

desired CLOSED position. When the gate is in the desired position, release the

button.

NOTE:

The GATE 1 right and left buttons can be used to jog the gate

back and forth as needed.

Press and release the LEARN LIMITS button. The control board will beep and the

SET CLOSE LIMITS LED will stop blinking.

Programming is now complete. If the SET OPEN LIMIT LED continues to blink, repeat

programming. If the problem continues, see below.
Test the limits by pressing the SINGLE BUTTON to open and close the gate.

ADJUSTMENT

» LEARN LIMITS

GATE 2 Left Button

GATE 1 Left Button

GATE 2 Right Button

GATE 1 Right Button

"BEEP"

LEARN LIMITS Button

"BEEP"

LEARN LIMITS Button

IF THE LIMITS WILL NOT PROGRAM

Disconnect both operators by pressing the reset switch on each operator to

RESET/DISCONNECT.

Manually close each gate.

Remove the learn limit cover and move the learn limit nut to the center position

on both operators.

Press the reset switch to NORMAL OPERATION on both operators.

Program the limits again.

1
2

LEARN LIMITS Button

Learn Limit Cover

Learn Limit Nut

Learn Limit Switch

Summary of Contents for Elite RSL12V

































Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands

Chamberlain Elite RSL12V, Installation Manual

Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands