Chamberlain Elite RSL12V Installation Manual Download

Page: 2 / 32

When you see these Safety Symbols and Signal Words on the following pages, they

will alert you to the possibility of serious injury or death if you do not comply with

the warnings that accompany them. The hazard may come from something

mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will alert you to the

possibility of damage to your gate and/or the gate operator if you do not comply

with the cautionary statements that accompany it. Read them carefully.

IMPORTANT NOTE

• BEFORE attempting to install, operate or maintain the operator, you must read

and fully understand this manual and follow all safety instructions.

• DO NOT attempt repair or service of your gate operator unless you are an

Authorized Service Technician.

MECHANICAL

ELECTRICAL

SAFETY

» SAFETY SYMBOL AND SIGNAL WORD REVIEW

TABLE OF CONTENTS

SAFETY 1-7

Safety Symbol and Signal Word Review

UL325 Model Classifications

Safety Installation Information

Gate Construction Information

Required Safety Protection Devices

Important Safety Information

6-7

INTRODUCTION 8

Operator Specifications

Carton Inventory

Hardware Inventory

INSTALLATION 9-11

Site Preparation

Types of Installations

Determine Location for Concrete Pad and Operator

Concrete Pad and Operator Attachment

Attach the Gate Brackets and Chain

WIRING 11-14

Earth Ground Rod

Power Wiring

12-13

Connect Batteries

Primary/Secondary Operators

ADJUSTMENT 15-20

Learn Limits

15-19

Force Adjustment

Test

PROGRAMMING 21

Remote Controls

Keyless Entry

Erase All Codes

Alternate Radio Receiver Installation

ADDITIONAL FEATURES

22-23

Timer-To-Close 22
Auto Open Jumper

Heater 22
Party Mode

Entrapment Protection Devices

OPERATION AND MAINTENANCE

24-25

Reset Switch

Remote Control

Sleep Mode

Maintenance 25
Battery

Drive Chain

TROUBLESHOOTING 26-29

Diagnostic Error Codes Chart

Troubleshooting Chart

27-28

Wiring Diagram

ACCESSORIES

WARRANTY

BACK COVER

Summary of Contents for Elite RSL12V

































Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands

Chamberlain Elite RSL12V, Installation Manual

Search results

Summary of Contents for Elite RSL12V

Reviews:

Related manuals for Elite RSL12V

Brands by name

Popular brands