Chamberlain CSW24U Installation Manual Download | Manualshive

Page: 51 / 60

background image

49

APPENDIX

Black Wire (-)

33AH Batteries

Red Wire (+)

J15 Plug
(new wire harness,
Model K94-37236)

10W

Red Wire (+)

Black Wire (-)

STEP 8 continued...

SOLAR PANEL(S)

WIRE THE SOLAR PANELS

1. Locate the J15 plug on the control board and unplug it from the

control board (it will not be used).

2. Install the new 33AH batteries using the tray as shown.

3. Connect the white jumper between the positive (+) terminal of one

battery to the negative terminal (-) of the other battery.

4. Route the battery wires (the longer set of wires) from the J15 plug

(new wire harness) through the lower, right, rear knockout (KO) in
the electrical box. Use the included adhesive wire clamps to route
the wires up the right side of the operator frame. Connect the red
wire to the positive (+) terminal of one battery. Connect the black
wire to the negative (-) terminal of the other battery.

5. Connect the red wire (+) from one solar panel to the black wire (-)

of the other solar panel.

6. Connect the shorter red wire (+) from the J15 plug (new wire

harness) labeled DC Power to the red wire on one solar panel.
Connect the shorter black (-) wire from the J15 plug (new wire
harness) labeled DC Power to the black wire from the other solar
panel.

7. Plug the J15 plug (new wire harness) into the J15 input on the

control board.

NOTE:

You may see a small spark when plugging the

J15 plug into the board.

Proceed to the Dual Gate section (if applicable) or proceed to the
Adjustment section.

40W solar panel

installation

60W solar panel

installation

Diode

10W

10W

10W

10W

10W

20W solar

panel

installation

Mounting Surface

Mounting Surface

Mounted Panel
Must Face South

INSTALL THE SOLAR PANEL

1. Position solar bracket on mounting surface. Mark and drill holes.

2. Insert two bolts into the track located on the back of the solar

panel(s).

3. Slide bolts in track away from bolt hole and align both bolts.

4. Secure solar panel(s) to solar bracket using two washered nuts.

5. Secure solar panel(s) assembly to mounting surface using appropriate

hardware.

«
...
49
50
51
52
53
...
»

Summary of Contents for CSW24U





























































Reviews:

No comments

Related manuals for CSW24U

Brand: vds Pages: 41

Brand: fadini Pages: 12

Brand: fadini Pages: 12

Brand: fadini Pages: 12

Brand: fadini Pages: 16

Brand: Roger Pages: 8

SlideSmart DC 10F

Brand: HySecurity Pages: 144

Brand: GarageAce Pages: 18

Brand: FAAC Pages: 8

HomeLink Genie Intellicode 2 GDO

Brand: Johnson Controls Pages: 5

EaziClean BCO-50

Brand: Lincoln Redco Pages: 2

Brand: CAME Pages: 22

Brand: Remote King Pages: 3

Brand: Chamberlain Pages: 32

Brand: DACE Pages: 52

Brand: Eagle Pages: 36

Brand: CAME Pages: 84

Brand: Johnson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands