Chamberlain CSW24U Installation Manual Download | Manualshive

Page: 19 / 60

background image

17

Power Wiring Connector
(120 Vac Socket, factory default)

240 VAC ONLY

The accessory outlet is disabled and cannot be used with the 240 Vac option.

1. Remove the outlet housing from the electrical box by removing the screws (2).

2. Pull the outlet housing out and locate the power wiring connector on the EMI board.

3. Unplug the power wiring connector from the 120 Vac socket (factory default location) and plug it into the 240 Vac socket.

4. Replace the outlet housing by securing with the screws. The operator is now set for 240 Vac operation.

Outlet Housing

240 Vac Socket

EMI Board

Junction Box Cover

120 VAC AND 240 VAC

1. Turn off the AC power from the main power source circuit breaker.

2. Run the AC power wires to the operator.

3. Remove the junction box cover.

4. Connect the green wire to the earth ground rod and AC ground using a wire nut.

NOTE:

The earth ground rod can be grounded to the chassis.

5. Connect the white wire to NEUTRAL using a wire nut.

6. Connect the black wire to HOT using a wire nut.

7. Replace the junction box cover. Ensure the wires are not pinched.

INSTALLATION

STEP 8 continued...

POWER WIRING

«
...
17
18
19
20
21
...
»

Summary of Contents for CSW24U





























































Reviews:

No comments

Related manuals for CSW24U

Brand: Chamberlain Pages: 44

Brand: Toona Pages: 24

Brand: Liftaway Pages: 19

Brand: RAMSET Pages: 25

Brand: King gates Pages: 29

Brand: BFT Pages: 20

Brand: Motorline professional Pages: 14

Brand: Tenpilot Pages: 24

Brand: Accessmatic Pages: 39

Brand: Remote King Pages: 3

Brand: tau Pages: 40

Brand: V2 Pages: 92

Brand: V2 Pages: 15

Brand: Home Master Pages: 47

Brand: fadini Pages: 12

GSM-4G-GATE-V10

Brand: GSM Activate Pages: 6

GSM-4G-GATE -V14

Brand: GSM Activate Pages: 7

Brand: GSM Activate Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands