Chamberlain CSW24U Installation Manual Download | Manualshive

Page: 28 / 60

background image

26

ERASE ALL CODES

1. Press and release the LEARN button (operator will beep and green

XMITTER LED will light).

2. Press and hold the LEARN button again until the green XMITTER LED

flashes and then release the button (approximately 6 seconds). All
remote control codes are now erased.

ERASE LIMITS

1. To erase the limits, press and hold the SET OPEN and SET CLOSE

buttons simultaneously (5 seconds) until both the SET OPEN and SET
CLOSE LEDs blink rapidly and the operator beeps.

2. Release the buttons and the SET OPEN and SET CLOSE LEDs will blink

slowly indicating the limits will need to be set.

LIFTMASTER INTERNET GATEWAY
(NOT PROVIDED)

PROGRAMMING

TO REMOVE AND ERASE MONITORED
ENTRAPMENT PROTECTION DEVICES

1. Remove the entrapment protection device wires from the terminal

block.

2. Press and release the SET OPEN and SET CLOSE buttons

simultaneously. The SET OPEN and SET CLOSE LEDs will turn on
(entering learn limit mode).

3. Press and release both SET OPEN and SET CLOSE buttons again to

turn off the SET OPEN and SET CLOSE LEDs (exiting learn limit
mode).

To program the operator to the LiftMaster Internet Gateway:

USING THE LEARN BUTTON ON THE OPERATOR’S
CONTROL BOARD

1. Connect the ethernet cable to the LiftMaster Internet Gateway and the

router.

2. Connect power to the LiftMaster Internet Gateway.

3. Create an online account by visiting www.myliftmaster.com.

4. Register the LiftMaster Internet Gateway.

5. Use an internet enabled computer or smartphone to add devices. The

LiftMaster Internet Gateway will stay in learn mode for three minutes.

6. Press the Learn button twice on the primary operator (the operator

will beep as it enters learn mode). The LiftMaster Internet Gateway
will pair to the operator if it is within range and the operator will beep
if programming is successful.

OR

USING THE RESET BUTTON ON THE OPERATOR

1. Connect the ethernet cable to the LiftMaster Internet Gateway and the

router.

2. Connect power to the LiftMaster Internet Gateway.

3. Create an online account by visiting www.myliftmaster.com.

4. Register the LiftMaster Internet Gateway.

5. Use an internet enabled computer or smartphone to add devices. The

LiftMaster Internet Gateway will stay in learn mode for three minutes.

6. Ensure gate is closed.

7. Give the operator an OPEN command.

8. Within 30 seconds, when the gate is at the open limit press and

release the reset button 3 times (on primary gate) to put primary
operator into High Band Learn Mode (the operator will beep as it
enters learn mode). The LiftMaster Internet Gateway will pair to the
operator if it is within range and the operator will beep if
programming is successful.

The status as shown by the LiftMaster Internet Gateway app will be either
“open” or “closed”. The gate operator can then be controlled through the
LiftMaster Internet Gateway app.

«
...
26
27
28
29
30
...
»

Summary of Contents for CSW24U





























































Reviews:

No comments

Related manuals for CSW24U

Brand: Wallace Perimeter Security Pages: 182

Brand: Hamilton Beach Pages: 20

Brand: Hamilton Beach Pages: 20

76375 - CleanCut Extra-Tall Can Opener

Brand: Hamilton Beach Pages: 10

Brand: Viking Pages: 49

Easy Touch 681131066235

Brand: GE Pages: 8

Brand: Essmann Pages: 10

Brand: DITEC Pages: 16

Brand: Nice Pages: 44

Brand: Remote King Pages: 3

BATTENTE ANGOLO

Brand: Dea Pages: 108

Brand: fadini Pages: 56

Brand: FAAC Pages: 22

Brand: JAGO Pages: 54

Brand: Calimet Pages: 16

Brand: Calimet Pages: 21

Brand: Calimet Pages: 18

Brand: GiBiDi Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands