Chamberlain CSW24U Installation Manual Download | Manualshive

Page: 24 / 60

background image

22

1. Remove the operator arm from the output shaft by releasing the

handle.

2. Align the tabs on the rear cover with the slots on the chassis and

place the cover over the operator.

3. Secure both sides of the rear cover to the chassis with two 5/16-18

lead in screws.

4. Reattach the operator arm to the output shaft (making sure the pin fits

into the slot) and secure by pushing the handle down.

5. Place the operator arm cover over the operator arm and secure.

6. Align the front cover with the back cover, making sure the grooves

line up.

7. Secure the front cover to the chassis with two 5/16-18 lead in screws.

8. Secure the front cover to the rear cover using the 5/16-18 lead in

screw.

The basic installation is complete.

STEP 11

INSTALL THE COVER

The operator cover consists of two pieces: a rear cover and a front cover. The front cover can easily be removed to access the electrical box. To access
the reset switch slide the access door up. The front cover and access door can be locked with the key.

TO LOCK THE ACCESS DOOR

From the factory the access door for the reset switch will not be locked.
To lock the access door follow the steps below:

1. Locate the lock tab on the back of the front cover and remove the

screw securing the tab to the cover.

2. Turn the tab 180 degrees, then secure with the screw. The access

door can now be locked.

Tabs on Rear Cover

Slots on
Chassis

Groove on Front Cover

5/16-18
Lead In
Screws

5/16-18
Lead In
Screw

Access Door

Lock Tab

Factory Default position

(back of front cover)

Access Door

INSTALLATION

«
...
22
23
24
25
26
...
»

Summary of Contents for CSW24U





























































Reviews:

No comments

Related manuals for CSW24U

Brand: DTS Pages: 19

Brand: Chamberlain Pages: 6

Brand: Viking Access Systems Pages: 52

Ditec NES1000EHP

Brand: Entre Matic Pages: 24

Brand: tau Pages: 40

SECURITY+ 2280 1/2 HP

Brand: Chamberlain Pages: 36

Brand: V2 Pages: 74

Brand: Radio Shack Pages: 4

Brand: TOPP Pages: 60

Brand: fadini Pages: 24

Brand: FAAC Pages: 13

Brand: GDS Pages: 15

Brand: Wayne-Dalton Pages: 21

Brand: Chamberlain Pages: 4

Brand: CAME Pages: 12

Brand: CAME Pages: 2

Brand: Kalorik Pages: 16

HINDI 880 SPRINT

Brand: fadini Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands