Chamberlain CSW24U Installation Manual Download | Manualshive

Page: 57 / 60

background image

55

POST-MOUNTING PLATE

For post-mounting model CSW24U commercial
swing operator (also CSW200 commercial swing
operator). Posts not included.
Model MPEL

REMOTE ANTENNA EXTENSION KIT

The remote antenna extension kit allows the
antenna to be remotely installed.
Model 86LM

WIRELESS ACCESS CONTROL RECEIVER

Access control receiver for up to 450 remote
controls.
Model STAR450-315

PLUG-IN LOOP DETECTOR

Conveniently plugs into existing control board.
Model LOOPDETLM

LOOP DETECTOR

Low power loop detectors mounted and wired
separately inside control box. LiftMaster low power
accessory.
Model LD7LP

VEHICLE SENSING PROBE

The vehicle sensing probe is buried in the ground
and can detect a car as it approaches and will then
open the gate.
Model CP3

SOLAR PANEL KIT

This kit is to replace or add a solar panel to the
operator application. 60W maximum for 24 Vdc
operators and 30W maximum for 12 Vdc
operators. Requires a 33AH battery harness.
Models SOLPNL10W12V (10 Watt, 12V),
SP10W12V* (10 Watt, 12V) and SP20W12V* (20
Watt, 12V)

MAGNETIC GATE LOCK

Outdoor magnetic lock, transformer, junction box,
mounting plate and hardware. Not for use with
Solar Applications. Must be powered separately.
Model MG1300

HEATER

The heater keeps the gearbox and batteries at a
suitable temperature when the outside temperature
is below -4°F. The thermostat MUST be set
between 45°F and 60°F to ensure proper gate
operation. The heater can be powered by 110 to
250 Vac.

Model HTR

MISCELLANEOUS

ACCESSORIES

BATTERIES

Gate access system batteries replace or upgrade the gate operator
batteries. Two identical 12 Vdc batteries are required for each gate
operator. Do not mix 7AH and 33AH batteries within a gate operator.

7AH BATTERIES

Standard 7 AMP-Hour Battery, 12 Vdc, to replace
original batteries provided with operator. Reuse
existing harnesses.

Models 29-NP712 (1) and K74-30762 (2)

33AH BATTERIES

Upgrade 33 AMP-Hour Battery, 12 Vdc. Ideal for
solar applications and extended battery backup.
Two required.
Model A12330SGLPK

BATTERY TRAY

For use with 33AH batteries.
Model K10-36183

33AH BATTERY HARNESS

Required for 33AH applications.
Model K94-37236

LIFTMASTER

®

INTERNET GATEWAY

Internet enabled accessory which connects to the
computer and allows you to monitor and control
gate operators and lighting accessories enabled
by MyQ

®

technology.

Model 828LM

MISCELLANEOUS

* Available end of 2015

WIRELESS COMMERCIAL KEYPAD

Durable wireless keypad with blue LED backlight
metal keypad, zinc-alloy metal front cover and 5
year 9V lithium battery. S 2.0

®

compatible.

Model KPW250

«
...
55
56
57
58
59
...
»

Summary of Contents for CSW24U





























































Reviews:

No comments

Related manuals for CSW24U

Brand: Cardin Elettronica Pages: 28

Estate Swing E-S 1100 Series

Brand: FAAC Pages: 53

Lids-Off OPEN-IT-ALL JW400

Brand: Black & Decker Pages: 2

Brand: PowerMaster Pages: 52

Brand: LockMaster Pages: 2

Brand: Jaytech Pages: 13

Brand: tau Pages: 40

Brand: Chamberlain Pages: 92

Brand: quiko Pages: 2

Brand: Beninca Pages: 14

Brand: tau Pages: 2

Brand: tau Pages: 16

Brand: EasyWay Pages: 43

Brand: CAME Pages: 96

Brand: CAME Pages: 28

Brand: Wayne-Dalton Pages: 26

Brand: lawrence doors Pages: 14

Brand: Cardin Elettronica Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands