Chamberlain CSW24U Installation Manual Download

Page: 10 / 60

Water Tight Conduit
(Not provided)

NOTE:

Power and control

wiring MUST be run in
separate conduits.

Operator

Earth Ground Rod

Check national and local
codes for proper depth

Warning Sign

Photoelectric
Sensors

Edge Sensor

Operator

Water Tight Conduit
(Not provided)

NOTE:

Power and control wiring

MUST be run in separate conduits.

Earth Ground Rod

Check national and local
codes for proper depth

Warning Sign

Photoelectric
Sensors

Edge Sensors

INTRODUCTION

OVERVIEW OF TYPICAL INSTALLATION

SINGLE GATE

DUAL GATE

Identify your installation type (refer to the Appendix in the back of the manual for more information).

NOTE:

One or more non-contact sensors

shall be located where the risk of
entrapment or obstruction exists at either
the opening or closing direction. Care shall
be exercised to reduce the risk of nuisance
tripping, such as when a vehicle, trips the
sensor while the gate is still moving.

Summary of Contents for CSW24U




























































Search results

Summary of Contents for CSW24U

Reviews:

Related manuals for CSW24U

Brands by name

Popular brands

Chamberlain CSW24U, Installation Manual

Search results

Summary of Contents for CSW24U

Reviews:

Related manuals for CSW24U

Brands by name

Popular brands