Chamberlain CSW24U Installation Manual Download | Manualshive

Page: 17 / 60

background image

15

CONTROL BOARD

CLOSE EYES/INTERRUPT (2 Terminals)

The CLOSE EYES/INTERRUPT input is for photoelectric sensor
entrapment protection for the close direction. When an obstruction is
sensed during gate closing the gate will open to the full open position and
resets the Timer-to-Close. This input will be disregarded during gate
opening.

CLOSE EDGE (2 Terminals)

The CLOSE EDGE input is for edge sensor entrapment protection for the
close direction. When an obstruction is sensed during gate closing the
gate will reverse to the full open position, disengaging the Timer-to-Close.
This input will be disregarded during gate opening.

OPEN EYES/EDGE (2 Terminals)

The OPEN EYES/EDGE input is for photoelectric sensor or edge sensor
entrapment protection for the open direction. When an obstruction is
sensed during gate opening the gate will reverse for 4 seconds then stop.
This input will be disregarded during gate closing.

EXPANSION BOARD (NOT PROVIDED)

EYE ONLY and COM

Open or Close Direction Photoelectric Sensors, the functionality is based
on the switch settings (located next to the terminals)

Switch set to CLOSE:

gate reverses fully when obstruction is sensed

Switch set to OPEN:

gate reverses 4 seconds when obstruction is sensed

EYE/EDGE and COM

Open or Close Direction Photoelectric Sensors or Edge Sensor, the
functionality is based on the switch settings (located next to the terminals)

Switch set to CLOSE:

gate reverses fully when obstruction is sensed

Switch set to OPEN:

gate reverses 4 seconds when obstruction is sensed

SHADOW INTERUPT EXIT

SBC

OPN

CLS

STP

COM

EYE

ONLY

EYE/

EDGE

EYE/

EDGE

COM

1

2

3

OPEN

CLOSE

T

O MAIN

BOARD

POWER

–

+
+
+

SBC

OPN

EDGE

COM

1

OPEN

CLOSE

T

O MAIN

BOARD

Photoelectric Sensors

Edge Sensor

Photoelectric Sensors

OR

Photoelectric Sensors

OR

Edge Sensor

There are three options for wiring the entrapment protection devices depending on the specific device and how the device will function. Refer to the
specific entrapment protection device manual for more information. These entrapment protection device inputs are for monitored devices, which
include pulsed photoelectric sensors, resistive edge sensors, and pulsed edge sensors.

Only one

monitored entrapment protection device may be

wired to each input.

Additional entrapment protection devices may be wired to the expansion board (not provided).

SHADOW INTERUPT EXIT

SBC

OPN

CLS

STP

COM

EYE

ONLY

EYE/

EDGE

EYE/

EDGE

COM

1

2

3

OPEN

CLOSE

T

O MAIN

BOARD

POWER

–

+
+

+

SBC

OPN

EYE

ONLY

EYE/

EDGE

EYE/

EDGE

COM

1

2

3

OPEN

CLOSE

T

O MAIN

BOARD

SBC

OPN

CLS

STP

COM

EYE

ONLY

EYE/

EDGE

EYE/

EDGE

COM

1

2

3

OPEN

CLOSE

T

O MAIN

BOARD

POWER

INSTALLATION

DIAGNOSTICS

Close Photoelectric Sensors

Close Edge

Open Edge

Open Photoelectric Sensors

OR

STEP 6 continued...

INSTALL ENTRAPMENT PROTECTION

Photoelectric Sensors

Photoelectric Sensors

Photoelectric Sensors

Edge Sensor

Edge Sensor

OR

OR

«
...
15
16
17
18
19
...
»

Summary of Contents for CSW24U





























































Reviews:

No comments

Related manuals for CSW24U

Brand: Wayne-Dalton Pages: 22

Brand: ACDC Pages: 20

Brand: FAAC Pages: 9

Brand: DoorHan Pages: 12

Brand: Chamberlain Pages: 286

Grand Openings EC1200 Series

Brand: Black & Decker Pages: 7

Brand: Black & Decker Pages: 2

Brand: Black & Decker Pages: 2

GRAND OPENINGS CO1200

Brand: Black & Decker Pages: 2

Grand Opening CO450BMC

Brand: Black & Decker Pages: 2

Brand: Black & Decker Pages: 2

Brand: Black & Decker Pages: 2

Brand: Waring Pages: 5

Brand: Normstahl Pages: 44

Brand: Sentex Pages: 31

Brand: FAAC Pages: 24

Brand: CAME Pages: 48

Brand: Beninca Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands