Chamberlain CSW24U Installation Manual Download | Manualshive

Page: 21 / 60

background image

19

Red (+) wire
from new wire
harness kit

Red (+)

Black (-)

Black (+) wire
from new wire
harness kit

33AH Batteries

White jumper from
new wire harness kit

J15 Plug

INSTALLATION

STEP 9 continued...

CONNECT BATTERIES

33AH BATTERIES

The batteries are charged in the circuit by the integrated transformer. The batteries are for battery backup or solar installation. The 33AH application
requires the 33AH wire harness (Model K94-37236) and an additional battery tray (Model K10-36183) to allow more space in the enclosure. The
heater option cannot be used with the 33AH battery application.

1. Locate the J15 plug on the control board and disconnect it.

2. Connect the white jumper from the 33AH wire harness kit between the positive (+) terminal of one battery and the negative (-) terminal of the other

battery.

3. Connect one end of the red (+) wire from the 33AH wire harness kit to the red wire from the J15 plug as shown. Connect the other end of the red

(+) wire to the positive (+) terminal on the battery as shown.

4. Connect one end of the black (-) wire from the 33AH wire harness kit to the black wire from the J15 plug as shown. Connect the other end of the

black (-) wire to the negative (-) terminal on the battery as shown.

5. Turn ON AC power to the operator.

6. Turn ON the AC power switch on the operator.

7. Reconnect the J15 plug to the control board.

NOTE:

You may see a small spark when plugging the J15 plug into the board.

«
...
19
20
21
22
23
...
»

Summary of Contents for CSW24U





























































Reviews:

No comments

Related manuals for CSW24U

Eagle-2000 series

Brand: Eagle Access Control Systems Pages: 26

Brand: CAME Pages: 20

Brand: Wayne-Dalton Pages: 32

Brand: 4Ddoors Pages: 44

Brand: Estate Swing Pages: 55

Brand: Nabco Pages: 32

Brand: MAG Pages: 9

4500DI-2DM 1/2 HP

Brand: Doit Pages: 40

Brand: RIB Pages: 48

Brand: Elvox Pages: 28

SMARTERHOME KASHWLGRGDA

Brand: Kogan Pages: 20

Brand: USAutomatic Pages: 60

Security+ 3110C

Brand: Chamberlain Pages: 72

Security+ 2245C

Brand: Chamberlain Pages: 72

Titano QK-T4000

Brand: quiko Pages: 9

Brand: HYDOM Pages: 16

Brand: Beninca Pages: 44

Brand: RIB Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands