background image

CENTURY

®

 warrants to the original purchaser that each new CENTURY wrecker or other CENTURY

products will be free from defects in material and workmanship for a period of twelve (12) months from
date placed in service, but in no event shall such warranty period exceed twenty-four (24) months from
date of manufacture by CENTURY. The purchaser must promptly notify CENTURY in writing of any
failure in material or workmanship. In no event shall CENTURY accept such notification later than
twenty-four (24) months from date of delivery or twelve (12) months from date placed in service,
whichever is earlier.

CENTURY’s obligation under this warranty, statutory or otherwise, is limited to the repair or
replacement at the CENTURY factory, or at a point designated by CENTURY, of such part or parts as
shall appear upon inspection by CENTURY to be defective in material or workmanship. New or
remanufactured parts will be used for any replacement at CENTURY’s option.

This warranty is not transferable.This warranty does not obligate CENTURY to bear the cost of labor or
transportation charges in connection with the repair or replacement of any parts found to be defective,
nor shall it apply to a product upon which repairs or alterations have been made unless authorized by
CENTURY.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, CENTURY MAKES NO OTHER
WARRANTY, EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. CENTURY shall in no event be liable for claimed
downtime, claimed loss of profits or goodwill, or any other special, incidental, indirect, or consequential
damages concerning or relating to any product or parts, whether based on negligence, strict liability,
breach of contract, breach of warranty, misrepresentation or any other legal theory, regardless of
whether the loss resulted from any general or particular requirement which CENTURY knew or had
reason to know about at the time of sale.

CENTURY MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY CENTURY
TO PURCHASER, including, but not limited to, any vehicle to which a CENTURY product may be
affixed or any accessories or wire rope, and CENTURY EXPRESSLY DISCLAIMS ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO
SUCH EQUIPMENT OR PRODUCTS. This language shall in no way affect or diminish the rights of the
purchaser to rely on such warranties as are extended by such manufacturers or suppliers. CENTURY
shall, to the extent permitted under applicable law, pass on to the purchaser such manufacturer’s or
seller’s warranty.

CENTURY, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the
following items, which are set forth by way of example and not limitation:

A. Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to

weather, road conditions, road treatments, etc.

B. Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure

to provide reasonable and necessary maintenance, or uses for which the equipment was not
designed or intended.

C. Alterations or modifications that affect performance, operation or reliability.
D. Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud flaps,

fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.

IT IS EXPRESSLY UNDERSTOOD THAT CENTURY MAKES NO IMPLIED WARRANTY THAT
CENTURY PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE
OR FOR ANY OTHER IMPROPER USE.

LIMITED WARRANTY

CENTURY

®

A Division of Miller Industries Towing Equipment Inc.

8503 Hilltop Drive 

 P.O. Box 120

Ooltewah, Tennessee 37363

Telephone (423) 238-4171

SERIAL NUMBER

REVISED 12/1/93

CENTURY

®

A Division of Miller Industries Towing Equipment Inc.

8503 Hilltop Drive 

••••

 Ooltewah, Tennessee 37363 

••••

 (423) 238-4171

Mailing Address: P.O. Box 120 

••••

 Ooltewah, Tennessee 37363 

••••

 Telex: 856967 CENWKRTN UD

Summary of Contents for 925































































































































Reviews: