Century 925 Installation, Operation, Maintenance, Parts Download | Manualshive

Page: 11 / 126

background image

I-5

Section I - SAFETY PRECAUTIONS (cont’d)

SAFETY TIPS

Death or serious injury can

occur when working near

power lines.

Learn - beforehand - as

much about your working

area as possible. Be sure

that exact locations of

overhead power lines, and

other obstructions or

hazards are known.

Don’t use winch cables with
hooks attached by means of
cable clips. Use only cables with
hooks attached by means of
thimbles and machine swaged
terminals.
USE CABLE CLIPS ONLY IN
THE EVENT OF AN
EMERGENCY FIELD
TEMPORARY REPAIR.
Use at least three clips spaced
3-4 inches apart and reduce the
cable working limit by 20%.
U-bolt of the clip should never be
around the live or long end of the
cable. Replace clips as soon as
possible with swaged cable
termination.

IVB-1

FIGURE 4B.1

2.

Turn steering wheel so that front wheels are directed straight
ahead.

3.

Insert latch of steering wheel lock into its buckle. Make sure
it locks in place. See Figure 4B.1.

4.

Place steering wheel grip on bottom of steering wheel and
secure it by tightening jam nut against sliding clamp.

5.

Hook seat grip under the front edge of auto seat or to a rigid
seat frame member that is securely fastened in place. Make
sure you do not hook it to a removable seat cushion.

6.

Grasp the free end of the belt and pull until belt is tight.

7.

Recheck jam nut to make sure it is still tight.

CARS WITH ANTI-THEFT STEERING LOCKS

SHOULD NEVER BE TOWED ON THEIR FRONT WHEELS

WHILE LOCKED IN THE TURNED POSITION

4B.1

INSTRUCTIONS FOR INSTALLATION

1.

Unlock anti-theft steering lock if vehicle is equipped with one.

STEERING WHEEL LOCK

Section IVB - OPERATING INSTRUCTIONS

«
...
9
10
11
12
13
...
»

Summary of Contents for 925































































































































Reviews:

No comments

Related manuals for 925

Brand: Massimo Pages: 115

Brand: Clam Corp Pages: 4

Brand: Clam Corp Pages: 6

Brand: Panther Pages: 16

Brand: TGB Pages: 109

Brand: Meec tools Pages: 56

Brand: Krone Pages: 128

Brand: Krone Pages: 192

2013 RANGER 500 EFI CREW Midsize

Brand: Polaris Pages: 14

Brand: Landoll Pages: 88

Brand: Yamaha Pages: 180

Wolverine YFM35XY

Brand: Yamaha Pages: 150

Brand: Polaris Pages: 325

BIG BEAR 4X4 YFM40FP

Brand: Yamaha Pages: 168

Brand: Yamaha Pages: 188

Brand: Smithco Pages: 36

TCV 2200 32-000

Brand: Smithco Pages: 54

Brand: RiMO Pages: 148

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands