manualshive.com logo in svg

Century 925, Installation, Operation, Maintenance, Parts

Share
Download
Century 925 Installation, Operation, Maintenance, Parts Download Page 54

Section IVA - OPERATING INSTRUCTIONS

WHEEL LIFT (cont’d)

IVA-8

4A.6

SECURING VEHICLE TO BE TOWED (cont’d)

(e) Repeat Safety Strap installation on opposite side of vehicle.

WHEN TOWING FROM REAR AXLES,

SECURE STEERING WHEEL OF VEHICLE IN TOW.

DO NOT RELY ON THE STEERING WHEEL

LOCKING DEVICE.

NOTE

IT MAY BE REQUIRED OF SOME VEHICLES TO REMOVE

THE HUB CAPS BEFORE MOUNTING TO THE WHEEL LIFT.

(f) Retract the Wheel Lift Boom using the Wheel Lift Extend

"IN/OUT" Control. Be certain there is enough clearance
between vehicle bumper and tailgate of the wrecker for sharp
turns.

NOTE

WHEN TOWING FROM REAR DRIVE AXLES,

PUT VEHICLE IN GEAR AND ENGAGE PARKING BRAKE.

WHEN TOWING FROM FRONT DRIVE AXLES,

PUT VEHICLE IN GEAR AND DISENGAGE PARKING BRAKE.

NOTE

THE CLOSER TO THE TAILGATE OF THE WRECKER

A VEHICLE IS TOWED, THE MORE FRONT END WEIGHT

WILL BE AVAILABLE FOR STEERING DURING TOW.

VII-10

Section VII - ELECTRICAL SCHEMATICS

WIRING PARTS LIST

PART

NUMBER

DESCRIPTION

NO.

REQ’D

0300134
0300188
0301601
0301671
0301800
0301909
0302380
0302558

7203001
7203002

7203003

5823031
5823032
5823033
5823034
5823035
5823036
5823037
5823044

CLAMP, 1" HOSE
CLAMP, 1-1/2" HOSE
CLAMP, 5/8" HOSE, INSULATED
TOW LIGHT SOCKET
JUNCTION BOX
RECEPTACLE BOOT
RELAY - SEALED & SKIRTED
HAND CONTROL ASSEMBLY

BODY HARNESS - GSA 925
HARNESS

WHEEL LIFT REMOTE & TOWLIGHT PLUG

HARNESS

FREEWHEEL, WORKLIGHT, & STATION

SOLENOID GROUND WIRE
TOOLBOX LIGHT HARNESS
TOOLBOX WIRE
RELAY GROUND WIRE
RELAY TRIGGER WIRE (YELLOW - LEFT TURN)
RELAY TRIGGER WIRE (GREEN - RIGHT TURN)
JUNCTION BOX GROUND WIRE
LIMIT SWITCH - TOOLBOX LIGHT

18
18
40

1
2
1
3
1

1
1

1

1
1
4
1
1
1
1
4

Summary of Contents for 925































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands