manualshive.com logo in svg

Century 925, Installation, Operation, Maintenance, Parts

Share
Download
Century 925 Installation, Operation, Maintenance, Parts Download Page 108

Section IV - OPERATING INSTRUCTIONS

WRECKER (cont’d)

IV-2

(c) Adjust engine speed to desired RPM using the Vernier Throttle

Control located on the left hand side of the wrecker body.

DO NOT EXCEED 1500 RPM

NEVER DRIVE TRUCK ON STREET WITH PTO ENGAGED,

THIS CAN CAUSE PUMP FAILURE DUE TO

OVER-SPEED AND OVERHEATING.

4.3 PREPARING TO LOAD VEHICLE (cont’d)

4.4 CABLE PAYOUT

Before operating any control handles, observe the winch cables to
make sure they are free and have sufficient slack to allow the boom to
extend. If not, payout cable by using the Cable "IN/OUT" Controls, or
switch on the Air-Operated Free Spool switch and manually pull
cables out to a sufficient length for boom extension.

4.5 BOOM ELEVATION

Elevate boom to the desired height by use of the Boom "UP/DOWN"
Control. See Figure 4.2.

Section VI - PARTS (cont’d)

VI-34

AIR OPERATED FREE SPOOL CLUTCH

FIGURE 4.2

Summary of Contents for 925































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands