Century 925 Installation, Operation, Maintenance, Parts Download

Page: 117 / 126

Section IVA - OPERATING INSTRUCTIONS

WHEEL LIFT (cont’d)

IVA-3

4A.4

WHEEL LIFT TOWING PREPARATION (cont’d)

approximately 3 inches by use of the Wheel Lift Extend
"IN/OUT" Control. See Figure 4A.4.

FIGURE 4A.4

(d) Due to the position of the disabled vehicle it may be

necessary to tilt the Wheel Lift to obtain the proper position
for pick-up. This may be accomplished by use of the
Wheel Lift Tilt "UP/DOWN" Control. See Figure 4A.5.

FIGURE 4A.5

4A.5

VEHICLE HOOK-UP

(a) After all preparations have been made as illustrated, back

the Wheel Lift until the crosstubes are firmly against the tires
of the vehicle to be towed. Take the truck out of gear and
apply parking brake.

VII-5

Section VII - ELECTRICAL SCHEMATICS

TOWLIGHT PLUG WIRING

REAR VIEW (FEMALE)

DETAIL "A"

TOWLIGHT PLUG

ORIENTATION

SEE DETAIL "A"

ALL WIRE #14 GAGE

YELLOW

GREEN

WHITE

BROWN

WHITE

YELLOW

WHITE

GREEN

ORANGE

JUNCTION BOX #1

JUNCTION BOX #2

RELAY

FROM CHASSIS

HARNESS

GREEN

YELLOW

BROWN

WHITE

COLOR CODES FROM JUNCTION BOX TO MME CONVERTER AND RELAYS

RED
WHITE
YELLOW
BROWN
GREEN
ORANGE

STOP
GROUND
LEFT TURN
RUNNING
RIGHT TURN
HOT (POWER)

#6 POLE
#4 POLE
#3 POLE
#2 POLE
#1 POLE
#12 POLE

COLOR CODES FROM CONVERTER TO MAGNETIC TOWLIGHTS - DETAIL "A"

(FEMALE PLUG)

YELLOW
GREEN
BROWN
WHITE

LEFT STOP & TURN
RIGHT STOP & TURN
RUNNING
GROUND

Summary of Contents for 925































































































































Search results

Summary of Contents for 925

Reviews:

Related manuals for 925

Brands by name

Popular brands

Century 925, Installation, Operation, Maintenance, Parts

Search results

Summary of Contents for 925

Reviews:

Related manuals for 925

Brands by name

Popular brands