Century 925 Installation, Operation, Maintenance, Parts Download Page 66

Page: 66 / 126

I-6

Section I - SAFETY PRECAUTIONS (cont’d)

SAFETY TIPS

Proper technique for using wire rope clips.
USE CABLE CLIPS ONLY IN THE EVENT OF AN EMERGENCY
FIELD TEMPORARY REPAIR.

RIGHT
WAY

WRONG
WAY

1. Turn back rope length specified in the chart. Apply first clip so

U-bolt is no less than the saddle width from the dead end. Tighten
nuts evenly and torque as specified.

2. Apply next clip as near loop as thimble will permit. Turn nuts on

firm, but do not tighten.

3. Space additional clips as indicated so distance between clips is

equal. Tighten all nuts evenly and torque as specified.

4. Apply the initial load and retighten all nuts to recommended torque

Inspect periodically and retighten as needed to the recommended
torque.

CLIP SIZE

INCHES

MINIMUM

NO. OF CLIPS

AMOUNT OF ROPE

TO TURN BACK

IN INCHES

TORQUE

IN FT.LBS.

3/8

7/16

1/2

9/16

5/8
3/4

2
2
3
3
3
4

6 1/2

11 1/2

12
12
18

45
65
65
95
95

130

This table is based on Crosby-Laughlin.

IVB-2

4B.2

INSTRUCTIONS FOR REMOVAL

Press button on buckle of steering wheel lock, releasing the
latch.

Loosen jam nut and remove grip from steering wheel.

Unhook seat grip from seat or seat frame.

FAILURE TO PROPERLY SECURE AND TIGHTEN

THE STEERING WHEEL LOCK

COULD RENDER IT INEFFECTIVE DURING TRAVEL,

RESULTING IN A DANGEROUS TOWING CONDITION

4B.1

INSTRUCTIONS FOR INSTALLATION (cont’d)

Section IVB - OPERATING INSTRUCTIONS

STEERING WHEEL LOCK

Summary of Contents for 925































































































































Search results

Summary of Contents for 925

Reviews:

Brands by name

Popular brands

Century 925, Installation, Operation, Maintenance, Parts

Search results

Summary of Contents for 925

Reviews:

Brands by name

Popular brands