Century 925 Installation, Operation, Maintenance, Parts Download | Manualshive

Page: 14 / 126

background image

I-8

Section I - SAFETY PRECAUTIONS (cont’d)

SAFETY TIPS

Don’t expect your wrecker to tow
loads equal to the wrecker rating.
Wrecker ratings apply to loads
imposed during recovery with the
wrecker properly stabilized.

Don’t pull a load with your winch
without making absolutely sure
that the winch drum clutch is
FULLY engaged.

Don’t attempt to recover heavy
loads without first estimating the
amount of pull that will be
required. Rig to keep the
estimated amount of pull well
within equipment ratings.

Don’t exceed ratings of booms,
cables, snatch blocks, or winches.
Stay within nameplate ratings.
Note that boom ratings decrease
significantly as boom is extended.

Section V - MAINTENANCE (cont’d)

5.3 LUBRICATION & PREVENTIVE MAINTENANCE (cont’d)

(b) Check hydraulic oil level in reservoir and fill to proper level.

Refer to 5.4, SUMMARY OF REQUIRED LUBRICANTS for
recommended oils to use.

(c) Replace hydraulic oil filters after first week of operation, then

every three (3) months thereafter.

(d) Inspect all bolts for tightness and re-tighten as necessary.

Vibration and stress may loosen even properly torqued bolts.

(e) Lubricate all grease fittings on the Wrecker and Wheel Lift weekly

including:

1.

Bellcranks and Control Handle Shafts

2.

Winch

3.

Cables

3

.

Cylinder Pivot Bearings

4

.

Cross Bar Pivot

5

.

Boom and Wheel Lift Slide Pads

6

.

Boom End Swivels

(f) All bearing surfaces not equipped with grease fittings should

be oiled using SAE 30 oil in a pump can.

(g) Check oil level of winches and fill to proper level, level plug

on end plates, with SAE 140 general purpose gear oil.

(h) Lubricate grease fitting on winch freespool clutch control.

(i)

Lubricate winch cables using an oily rag while respooling onto
drum. Other special cable lubricants are available which have
better penetrating qualities. Consult your local oil company for
a list of these.

V-2

«
...
12
13
14
15
16
...
»

Summary of Contents for 925































































































































Reviews:

No comments

Related manuals for 925

Brand: Polaris Pages: 118

Brand: Can-Am Pages: 58

Brand: OTIS Pages: 17

Brand: Dynacraft Pages: 31

2009 Outlander 500 EFI

Brand: Can-Am Pages: 152

Adapt-X Optimax

Brand: Apogee Pages: 24

Brand: Norsjö Pages: 32

Brand: Ventrac Pages: 83

Brand: Aero Pages: 32

Chem-Veyor 2614D

Brand: Walinga Pages: 28

Brand: Baja motorsports Pages: 44

Quad Lander 250

Brand: Sym Pages: 223

Brand: Rato Pages: 118

Brand: Yamaha Pages: 176

Brand: Yamaha Pages: 156

Brand: Landa Pages: 14

Brand: Erde Pages: 6

Brand: Pongratz Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands