manualshive.com logo in svg

Century 925, Installation, Operation, Maintenance, Parts

Share
Download
Century 925 Installation, Operation, Maintenance, Parts Download Page 60

NOTES

Section IVA - OPERATING INSTRUCTIONS

WHEEL LIFT (cont’d)

IVA-14

4A.12

TOW FORK & ADAPTER APPLICATIONS

(a) Align Wheel Lift with disabled vehicle.

NOTE

STEPS (b) THROUGH (d) ARE NOT NECESSARY

PERMITTING THE AXLE IS HIGH ENOUGH TO ALLOW
EXTENSION OF BOOM WITH FORKS AND ADAPTERS

INSTALLED ON CROSSBAR.

(b) Extend the Boom (without adapters or forks) until crossbar

is centered with axle of disabled vehicle.

(c) Raise vehicle until tire can be blocked up high enough to allow

forks to clear axle when installed onto the crossbar.

(d) Block up tires and lower Boom until boom can be retracted

for installation of adapters and forks.

(e) Install adapters in desired configuration on crossbar. Select

and install desired forks into adapters. Refer to Figure 4A.19.

(f) Extend Boom until Forks are beneath axle or frame as desired.
(g) Manually adjust adapters on crossbar to a point where the

forks will come in contact with the frame or axle in the desired
towing position.

(h) Tighten "T" Handles on adapters. Attach safety chains

around axle or frame, crossbar and forks as shown in
Figure 4A.19.

Summary of Contents for 925































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands