background image

11

5.3 -  Starting / Stopping the unit

With the unit in the Local off mode: 
To display the list of operating modes and select the required 
mode, press the 

Start/Stop 

button 

 in the upper-right 

corner of the Synoptic screen.

IMPORTANT:

 When entering the menu, please note that 

the currently selected item corresponds to the last running 
operating mode. 

This screen is displayed only when the unit is currently not 

running..If.the.unit.was.in.the.running.state,.then.the.Confirm.

stop message would be displayed (see below).

Press 

 or 

 to go to the next page.

Local On

Local On: The unit is in the local control mode and allowed 

to start.

Local 

Schedule

Local Schedule: The unit is in the local control mode and 

allowed to start if the period is occupied.

Network

Network: The unit is controlled by network commands and 

allowed to start if the period is occupied.

Remote

Remote: The unit is controlled by external commands and 

allowed to start if the period is occupied.

Master

Master: The unit operates as the master in the master/slave 

assembly and allowed to start if the period is occupied.

To start the unit

1. Press the 

Start/Stop 

button.

2. Select the required Machine Mode.
3. The Welcome screen will be displayed.

To stop the unit 

1. Press the 

Start/Stop

 button.

2..Confirm.the.unit.shutdown.by.pressing.

Confirm Stop 

or 

cancel the unit shutdown by pressing the 

Back

 button. 

The bell located in the upper-right part of the 
screen lights when any fault is detected.

5 -  

SETTING UP TOUCH PILOT JUNIOR CONTROL

5.1 -  Reading the Welcome screen

The.Welcome.screen.is.the.first.screen.shown.after.starting.

the user interface. It displays the application name as well as 
the current software version number.

•  To exit the Welcome screen and go to the Home screen 

(see section 4.3), press the

 Home

 button 

 .

1

Home button

2

Software version number

3

Information message box

Information message box

The information displayed in the status bar at the bottom of 
the screen includes relevant messages regarding the current 
user action. All screens presented further in this manual may 
display the following messages:

MESSAGE

STATUS

COMMUNICATION 

FAILURE!

Equipment controller did not respond while 

reading the table content.

ACCESS DENIED!

Equipment controller denies access to one 

of the table data blocks.

LIMIT EXCEEDED!

The value entered exceeds the table limits.

Save changes?

Modifications have been made. The exit must 

be confirmed by pressing Save or Cancel.

HIGHER FORCE IN 

EFFECT!

Equipment controller rejects Force or Auto 

command.

Too many users connected! 

Please try again later ...

Too many users connected at the same time 

(WEB INTERFACE ONLY)

5.2 -  Exploring the Synoptic screen

The Synoptic screen provides an overview of the system control, 
allowing the user to monitor the vapour-refrigeration cycle. 
The diagram indicates the current status of the unit, giving 
information on the unit capacity, the status of water heat 

exchanger.pumps,.and.the.pre-defined.setpoint.parameter.

Press the 

Main menu 

button 

 to access all unit functions.

IMPORTANT:

 The Synoptic screen display may vary 

depending on pumps and OAT sensor availability.

1

2

3

Summary of Contents for AquaSnap 30WG Series





































Reviews: