2
Remote control
Memorising a channel
1) Press and hold down button "
P2
": LED "
L2
" will flash.
2) At the same time activate the transmitter channel to be memorised, "
L2
" will flash 3 times indicating that the
channel has been memorised; if the LED keeps flashing slowly the channel was already memorised. Only one
channel can be memorised at a time. To insert another channel repeat points 1 and 2 after having released the
button. When the code memory is complete (20 transmitters each with 4 channels memorised) you may only
memorise a new transmitter after you have completely cancelled an existing transmitter (all the buttons) or after
cancelling the entire memory content.
Cancelling a channel
1) Press the button "
P2
" twice and hold down after pressing the second time: LED "
L2
" will flash at brief inter-
vals.
2) Activate the transmitter channel to be cancelled until the LED flashes 3 times.
To cancel another channel repeat points 1 and 2 after having released the button.
Cancelling the entire memory content
Press "
P2
" three times and hold down after pressing the third time. During the cancellation procedure (3-4 seconds)
LED "
L2
" remains lit.
After cancellation the LED will flash 3 times; at this point release the button.
Memorising ulterior channels via radio
• Memorisation can be activated
via radio
(without opening the receiver container) if jumper "
J
" has been
inserted. Activation will be indicated by the buzzer sounding.
1) Using a transmitter, in which at least one channel button "A,B,C or D" has already
been memorised in the receiver, press the button "
MR
" as shown in the figure.
Note:
all the receivers within range when the channel button is pressed (and which
have at least one of the transmitter channel buttons memorised) will activate their
signal buzzer "
B
" (fig. 1).
2) To select the receiver in which to memorise the new code activate one of the channels on the same transmit-
ter. The receivers which do not contain that channel code will sound a five-second long "
beep
" and will then
deactivate. The receivers which contain the channel code will sound a one-second long "
beep
" and will enter
the "
programming via radio
" mode.
3) Press the channel buttons on the pre-selected transmitter that you wish to memorise; the receiver will sound
2 "
beeps
" of half a second each after which the receiver will be ready to receive another code.
4) To leave the programming mode wait for 3 seconds without memorising any codes. The receiver will sound a
five-second long "
beep
" and will then exit the programming mode.
When the memory is entirely occupied the buzzer will sound 10 rapid "
beeps
" and will automatically leave the
"
programming via radio
" mode. The same signal is given each time you try to enter "
programming via radio
"
when the memory is full.
MANAGING THE DISPLAY KEYBOARD LCD AND LED
(fig. 2)
It is possible to use the
MDK RT/MDK RTL
to activate single or groups of radio programmers: The command will
have to be memorised in the radio programmer.
Note:
the "general" command will activate all devices that have at least one command memorised.
Memorising a single or group command
)
1) Press and hold down button "
P2
" on the radio programmer (LED "
L2"
will flash slowly).
2) - for a single command: select the unit using buttons 4 and 6;
- for a group command: press button 5 and then select the group using buttons 4 and 6.
3) Press button 1 to send the command: LED "
L2"
will flash 3 times to confirm memorisation; if the LED contin-
ues to flash slowly the code is already stored in memory. To insert another code repeat points 1 to 3 after first
releasing button "
P2
". Up to 4 keyboards can be memorised.
Cancelling a single or group command
1) Press button "
P2
" twice and hold down (LED "
L2
" will flash at brief intervals).
2) - for a single command: select the unit using buttons 4 and 6;
- for a group command: press button 5 and then select the group using buttons 4 and 6.
3) Press button 1 to send the command: LED "
L2"
will flash 3 times to confirm cancellation. To insert another
code repeat points 1 to 3 after first releasing button "
P2
".
Cancelling everything "single command/group/general"
1) Press button "
P2
" twice and hold down (LED "
L2
" will flash at brief intervals)
2) Press button 5.
3) Press button 1 to send the "general" command: LED "
L2"
will flash 3 times to confirm the cancellation of the
keyboard.
For more information regarding the
LCD/LED
keyboards see the instructions supplied with the product.
MEMORIZZAZIONE CODICE TX-RX
RCQ449100
13-04-2001
DM0531
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
MR
