manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 424 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 424

4

4

4-348

4-348

Disassembly/Assembly > Pickup And Feeding System > Removing the Duplex Solenoid (MF4820d) > Proce

d

ure

Disassembly/Assembly > Pickup And Feeding System > Removing the Duplex Solenoid (MF4820d) > Proce

d

ure

2)Free the solenoid harness[1] from the guide[A], and put it through the hole[B] of the right 

side plate to the outside.

[2]

[A]

[1]

[B]

3)Remove the duplex solenoid[1].

[1]

[2]

F-4-957

F-4-958

Caution:
When mounting the duplex solenoid, align the solenoid lever [1] with the groove in 
the link [2], and insert the 2 solenoid positioning protrusions [3] into the 2 positioning 
holes [4] in the side panel to mount the solenoid.

[4]

[3]

[1]

[2]

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments