Canon FAXPHONE L190 Service Manual Download Page 145

Page: 145 / 511

4-69

Disassembly/Assembly > Document Exposure/Feeder System > Removing the SADF Pickup Roller 1,2 (MF4870dn/MF4830d) > Procedure

2)Remove the SADF upper cover[1].
2 shafts[2]

[1]

[2]

3)Remove the gear[1],bushing[2],2 e-rings[3] and bushing[4]

Caution:

Do not touch the pickup roller surface[1].

[1]

F-4-169

4)Remove the pickup roller unit[1].

[1]

5)Remove the spring[1] on the back side of the pickup roller unit.

[1]

F-4-170

F-4-171

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAXPHONE L190

Reviews:

Canon FAXPHONE L190, Service Manual, Page: 145 / 511

Search results

Summary of Contents for FAXPHONE L190

Reviews: