Canon FAXPHONE L190 Service Manual Download Page 366

Page: 366 / 511

4-290

Disassembly/Assembly > Fixing System > Removing the Fixing Assembly (MF4890dw/MF4880dw) > Procedure

3)Remove the harness retaining spring[1] from the hook[2], and free the harness[3] from the
guide[A].

[1]

[2]

[3]

[A]

4)Remove the 2 left/right reinforcing plates[1]
• 4 screws(black TP)[2]

[2]

[1]

5) Remove the 4 connectors [1].
6) Disengage the harness [2] from the harness guide [A].

F-4-788

F-4-789

7) Disengage the fixing harness [4] from the harness holder [3].

[1]

[4]

[3]

[A]

[2]

8) Remove the harness holder [1].
• 1 claw [2]

[1]

[2]

F-4-790

F-4-791

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAXPHONE L190

Reviews:

Canon FAXPHONE L190, Service Manual, Page: 366 / 511

Search results

Summary of Contents for FAXPHONE L190

Reviews: