manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 142 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 142

4

4

4-66

4-66

Disassembly/Assembly > Document Exposure/Feeder System > Removing the SADF Pickup Unit (MF4870dn/MF4830d) > Procedure

Disassembly/Assembly > Document Exposure/Feeder System > Removing the SADF Pickup Unit (MF4870dn/MF4830d) > Procedure

3)Remove the SADF front cover[1].
•  2 claws[2]
•  2 bosses[3]

Caution:

When releasing the 2 claws[2] on the SADF front cover, be careful not to put too 
much force, otherwise they may get damaged.

x2

[3]

[2]

[1]

Note:

The following shows the 2 claws[2] and 2 bosses[3] of the SADF front cover.

[3]

[3]

[2]

F-4-160

4)Free the boss[1], and open the SADF upper cover[2] by the amount for which the boss is 

freed.

[2]

[1]

5)Free the harness[1] from the guide[A], and remove the 4 screws[2] on the right and left.

x4

[1]

[A]

[2]

[2]

6)Remove the SADF pickup unit.

[1]

F-4-161

F-4-162

F-4-163

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments