Canon FAXPHONE L190 Service Manual Download Page 364

Page: 364 / 511

4-288

Disassembly/Assembly > Image Formation System > Removing the Transfer Roller (L418S/L410/L190) > Proce

ure

Disassembly/Assembly > Image Formation System > Removing the Transfer Roller (L418S/L410/L190) > Proce

ure

3) Hold both shafts [1] of the transfer roller and remove the roller [2].

Caution:

When installing the transfer roller to the host machine, be sure to fit the protrusion[2]
to the spring[1]

[1]

[2]

[1]

[2]

[1]

F-4-783

F-4-784

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAXPHONE L190

Reviews:

Canon FAXPHONE L190, Service Manual, Page: 364 / 511

Search results

Summary of Contents for FAXPHONE L190

Reviews: