manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 228 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 228

4

4

4-152

4-152

Disassembly/Assembly > Controller System > Removing the Toner Sensor and Multi Pickup Sensor Unit (MF4890dw/MF4880dw) > Proce

d

ure

Disassembly/Assembly > Controller System > Removing the Toner Sensor and Multi Pickup Sensor Unit (MF4890dw/MF4880dw) > Proce

d

ure

Caution:
When mounting the scanner cover, pass the shutter open/close lever [1] through the
hole [A] in the scanner cover.

[1]

[A]

F-4-366

Caution:
Ensure that the shutter open/close lever [1] can move vertically.

[1]

F-4-367

2)Disconnect the 2 connectors[1], and put it through the hole[A] of the left side plate to the 
inside.

[A]

[A]

[1]

[1]

x2

3)Remove the drum unit[1].

[1]

F-4-368

F-4-369

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments