manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 240 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 240

4

4

4-164

4-164

Disassembly/Assembly > Controller System > Removing the Engine Controller PCB (MF4870dn/MF4830d) > Proce

d

ure

Disassembly/Assembly > Controller System > Removing the Engine Controller PCB (MF4870dn/MF4830d) > Proce

d

ure

x2

[1]

[2]

[3]

2)Disconnect the terminal[1], free the harness[2] from the harness guide[A], and then put it 
through the hole[B].

[1]

[2]

[A]

[2]

[B]

F-4-402

F-4-403

Caution:
When connecting the terminal[1], be sure that the contact spring[2] is in contact with 
it.

[2]

[1]

F-4-404

3)Remove the harness spring[1] from the hook[2], and free the harness[3] from the guide[A].

[1]

[2]

[3]

[A]

F-4-405

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments