manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 369 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 369

4

4

4-293

4-293

Disassembly/Assembly > Fixing System > Removing the Fixing Assembly(MF4870dn/MF4830d) > Procedure

Disassembly/Assembly > Fixing System > Removing the Fixing Assembly(MF4870dn/MF4830d) > Procedure

Caution:
When connecting the terminal[1], be sure that the contact spring[2] is in contact with 
it.

[2]

[1]

F-4-799

3)Remove the harness retaining spring[1] from the hook[2], and free the harness[3] from the 
guide[A].

[1]

[2]

[3]

[A]

F-4-800

4)Remove the 2 left/right reinforcing plates[1]
•  4 screws(black TP)[2]

x4

[2]

[2]

[1]

[1]

5) Remove the 4 connectors [1].
6) Disengage the harness [2] from the harness guide [A].
7) Disengage the fixing harness [4] from the harness holder [3].

[1]

[1]

[4]

[3]

[A]

[2]

x4

F-4-801

F-4-802

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments