manualshive.com logo in svg

Canon FAXPHONE L190, Service Manual, Page: 115 / 511

Share
Download
Canon FAXPHONE L190 Service Manual Download Page 115

4

4

4-39

4-39

Disassembly/Assembly > External Cover, Interior > Removing the Upper Cover (MF4720w/MF4712/MF4710) > Procedure

Disassembly/Assembly > External Cover, Interior > Removing the Upper Cover (MF4720w/MF4712/MF4710) > Procedure

4)Raise the delivery tray[1] vertically and remove it.

[1]

5)Remove the upper cover[1]
•  6 screws(black TP)[2]

[2]

x6

[1]

[2]

F-4-96

F-4-97

Caution:
Be sure to put the cartridge arm[1] through the hole[A] of the  upper cover when 
installing

[1]

[A]

F-4-98

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Reviews:

No comments