Canon FAXPHONE L190 Service Manual Download Page 407

Page: 407 / 511

4-331

Disassembly/Assembly > Pickup And Feeding System > Removing the Pickup Solenoid (MF4870dn/MF4830d) > Procedure

Caution:
When connecting the terminal[1], be sure that the contact spring[2] is in contact with
it.

[2]

[1]

F-4-913

3)Remove the harness retaining spring[1] from the hook[2], and free the harness[3] from the
guide[A].

[1]

[2]

[3]

[A]

F-4-914

4)Remove the harness retaining spring[1] and 4 connectors[2].

[1]

[2]

5)Free the pickup solenoid harness[1] from the harness guide[A]

[1]

[A]

F-4-915

F-4-916

Summary of Contents for FAXPHONE L190
































































































































































































































































































































































































































































































































Search results

Summary of Contents for FAXPHONE L190

Reviews:

Canon FAXPHONE L190, Service Manual, Page: 407 / 511

Search results

Summary of Contents for FAXPHONE L190

Reviews: