Canon CX 350 User Manual Download Page 108

Page: 108 / 132

Troubleshooting

101

No (Color) ink.

The ink cartridge of
the displayed color
(Light Magenta,
Light Cyan, Yellow,
Magenta, Cyan or
Black) is empty.

Replace the empty ink cartridge with a new one.

5.3 Replacing Ink Cartridges

Residual ink
receiver set error.

The residual ink
receiver is not set
correctly.

Reset residual ink receiver and make sure that it is
mounted correctly.

5.5 Replacing the Residual Ink Receiver

Residual ink
receiver full.

The residual ink
receiver is full.

Replace the old residual ink receiver with a new
one.

5.5 Replacing the Residual Ink Receiver

Paper size error.

The paper loaded
in the feeder lift tray
is not the same size
as the size selected
in the software
application or the
printer driver.

Check the paper size settings.

Paper jam.

Paper is jammed
inside the printer.

Open the PHS door and remove the jammed paper.

6.2 Paper Jams

Check the stacker and make sure that it is installed
correctly.

Attaching the Stacker

Paper overloaded.

The amount of
paper loaded in the
feeder lift tray is
over the limit.

Open the feeder cover and make sure that the top of
the stack is not higher than the arrow that the load
limit mark shows.

load limit mark

Paper load error.

The paper is not
loaded correctly in
the feeder lift tray.

Reload the paper and try again.

No paper.

No paper loaded.

Load paper in the feeder lift tray.

Error Message

Problem

Solution

Summary of Contents for CX 350





































































































































Search results

Summary of Contents for CX 350

Reviews:

Related manuals for CX 350

Brands by name

Popular brands

Canon CX 350, User Manual

Search results

Summary of Contents for CX 350

Reviews:

Related manuals for CX 350

Brands by name

Popular brands