Canon CanoScan D1230UF User Manual Download Page 36

Page: 36 / 115

chapter 4

What is on the
Screen?

Top Page

Glossary

Contents

Index

Image Source

Specifies the source of the original.

•

Platen

Scans the photos or documents.

•

Film

Scans films from the Film Adapter Unit (FAU).

Changing the Image Source clears the image from the
Preview area and clears all settings set with the Toolbar
and Tone sheet buttons.

Paper Size

Specifies the paper size of the image to be scanned.

Changing the Paper Size clears the Preview area and
clears all settings set with the Toolbar and Tone sheet
buttons.

• Business Card
• Statement
• B5
• Executive
• Letter
• A4
• Full Platen
• L Portrait
• L Landscape
• LL Portrait
• LL Landscape
• Postcard (4”x6”)

Note

Summary of Contents for CanoScan D1230UF




















































































































Search results

Summary of Contents for CanoScan D1230UF

Reviews:

Related manuals for CanoScan D1230UF

Brands by name

Popular brands

Canon CanoScan D1230UF, User Manual

Search results

Summary of Contents for CanoScan D1230UF

Reviews:

Related manuals for CanoScan D1230UF

Brands by name

Popular brands