Canon CanoScan D1230UF User Manual Download Page 19

Page: 19 / 115

chapter 2

Installing
ScanGear CS-U

Top Page

Glossary

Contents

Index

Uninstalling ScanGear CS-U

•Always uninstall ScanGear CS-U with this procedure using

the CanoScan Setup Utility CD-ROM

•Make sure the scanner is connected to the computer.

Place the CanoScan Setup Utility CD-ROM in the drive.

Click [Uninstall the Software] in the CD-ROM’s menu window.

Click [Uninstall ScanGear CS-U] in the Uninstall menu window.

Windows Me / 98 :

Click [Yes] in the comfirmation dialog.

Windows 2000 :

Scanners and Cameras property dialog displays.

Select [CanoScan D1230U] or [CanoScan D2400U] and click
[Remove].

If you will re-install ScanGear CS-U, restart the computer.

Note

Summary of Contents for CanoScan D1230UF




















































































































Search results

Summary of Contents for CanoScan D1230UF

Reviews:

Related manuals for CanoScan D1230UF

Brands by name

Popular brands

Canon CanoScan D1230UF, User Manual

Search results

Summary of Contents for CanoScan D1230UF

Reviews:

Related manuals for CanoScan D1230UF

Brands by name

Popular brands