background image

Oilless Compressors

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. 
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or 
property damage! Retain instructions for future reference.

Description 

Portable oilless air compressors are for 
home and workshop use. Cleaning or 
replacement of the inlet filter on all 
models and draining moisture from the 
air receivers are required maintenance. 

Safety Guidelines

This manual contains information that is 
very important to know and understand. 
This information is provided for SAFETY 
and to PREVENT EQUIPMENT PROBLEMS. 
To help recognize this information, 
observe the following symbols. 

 

Danger indicates  

  an imminently 

hazardous situation which, if not avoided, 
will result in death or serious injury.
 

warning indicates  

  a potentially 

hazardous situation which, if not avoided, 
coulD result in death or serious injury.
 

caution indicates a  

  potentially 

hazardous situation which, if not avoided, 
MAY result in minor or moderate injury.
 

Notice indicates  

  important 

information, that if not followed, MAY 
cause damage to equipment.

Unpacking

When unpacking unit, inspect carefully 
for any damage that may have occurred 
during transit. 

Make sure any loose 

fittings, bolts, etc., are tightened before 
putting unit into service. In case of 
questions, damaged or missing parts, 
please call 1-800-543-6400 for customer 
assistance. Have the serial number, 
model number, and part

s list (with 

missing parts circled) before calling.

  Operating Instructions    

HU3501

Breathable Air warning

This compressor/pump is not 
equipped and should not be 
used “as is” to supply breathing 
quality air. For any application of 

air for human consumption, the 

air compressor/pump will need 
to be fitted with suitable in-line 
safety and alarm equipment. 
This additional equipment is 

necessary to properly filter 
and purify the air to meet 
minimal specifications for Grade 
D breathing  as described in 

Compressed Gas Association 
Commodity Specification G 7.1 
- 1966, OSHA 29 CFR 1910. 134, 
and/or Canadian Standards 
Associations (CSA).

DISCLAIMER OF WARRANTIES
In the event the compressor is 

used for the purpose of breathing 
air application and proper in-line 
safety and alarm equipment is 
not simultaneously used, existing 
warranties shall be voided, and 
Campbell Hausfeld disclaims any 

liability whatsoever for any loss, 
personal injury or damage.

General Safety

CALIFORNIA PROPOSITION 65

 

 This product or 

   its power cord may 

contain chemicals, including lead, known 
to the State of california to cause cancer 
and birth defects or other reproductive 
harm. wash hands after handling.
 

You can

  create 

dust when you cut, sand, 
drill or grind materials such 
as wood, paint, metal, 
concrete, cement, or other 
masonry. This dust often contains 
chemicals known to cause cancer, birth 
defects, or other reproductive harm. 
wear protective gear.

IN630800AV 5/09

GENERAL SAFETY INFORMATION

Air compressors are utilized in a variety 
of air system applications. Because air 
compressors and other components 
(material pump, spray gun, filters, 
lubrications, hoses, etc.) used make up 
a high pressure pumping system, the 
following safety precautions should be 
observed at all times. Only persons well 
acquainted with these rules of safe 
operation should be allowed to use the 
air compressor.

 

 All electrical work  

   should be done by a 

qualified (licensed or certified) 
electrician. on a properly wired circuit, 
the black wires supply a voltage 
potential even when the unit is off.

© 2009 Campbell Hausfeld/Scott Fetzer

For parts, product & service information

visit 

www.chpower.com

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.

See Warranty on page 8 for important information about commercial use of this product.

Record the Model No., Serial No. and 

date of purchase located on the base 

below the pump in the space below.
Model No. 

____________________

Serial No. 

____________________

Date of purchase _________________

Retain these numbers for future 

reference.

STOP!

DO NOT RETURN  
THE PRODUCT TO  
THE RETAILER!

Summary of Contents for HU3501

























Reviews: