background image

14 

Operating instructions V604s Be 

Camille Bauer

Address

Description

Data  type

#

Default

Description

40547

TSET

REAL

1.0

Settling time (99%) [s] (1 … 30)

Automatic parameter correction

2

40549

SETTING

UINT16

00h

Settings

Bit

Description

0
1
2
3
4

Recognition of the type of connection (2L, 3L, 4L) after reset
Input 1: Breakage monitoring activated
Input 2: Breakage monitoring activated
Input 1: Short circuit monitoring activated
Input 2: Short circuit monitoring activated

40550

MATRIX

UINT8

Linking of inputs with outputs

0

01h

Output 1:

00h:  

Not used

01h: Input 

1

02h: Input 

2

03h:  

Input 1 + 2

04h:  

Input 1 – 2

05h: 

Input 2 – 1

06h: 

Input 1 * 2

07h:  

Minimum value (Input 1,2)

08h:  

Maximum value (Input 1,2)

09h:  

Mean value (Input 1,2)

81h: 

Sensor redundancy: Input 1 normally

82h: 

Sensor redundancy: Input 2 normally

87h:  

Sensor redundancy: Minimum value (Input 1,2)

88h:  

Sensor redundancy: Maximum value (Input 1,2)

89h:  

Sensor redundancy: Mean value (Input 1,2)

- Only measured variables of the same unit may be linked.
- Product formation: Only possible for combinations V*mV, V*mA, mA*mA, mV*mA and mV*mV.

Sensor redundancy 
- Measured variable in case of a fault:  
  

INPUTx which does not show a fault

- Limitations:
  

- The same measuring range for both inputs

  

- The same scaling factors (always 1.0)

  

- No output value in case of a fault

 - 

Temperature 

measurement

 

- Breakage or short circuit monitoring active

1

00h
at 2xmA:
02h

Output 2 (same as Output 1)

40551

LIMITA

UINT8

Setting of limit values

0

0

Measured variable for Limit value 1

Bit

Description

0-4

6
7

Limit value 

0: Not used

 

1: Input 1 (INPUT1)

 

2: Input 2 (INPUT2)

 

3: Measured variable Output 1 (MEAS1)

 

4: Measured variable Output 2 (MEAS2)

 

5: Input 1 – Input 2

 

6: Input 2 – Input 1

Absolute value of measured variable for the limit value
1: Gradient dx/dt

Note: Drift monitoring is realised by difference calculation.
Only measured variables of the same unit may be linked.

1

0

Measure variable for Limit value 2 (same as Limit value 1)

Summary of Contents for SINEAX V604s




















Reviews: