background image

Camille Bauer 

Operating instructions V604s Be 

11

6.6 Confi guration parameters

Settings

Address

Description

Data  type

#

Default

Description

40515

DEVADDR

UINT16

01h

MODBUS Slave address (1…247)

40516

MODBUS

UINT16

3222h

MODBUS settings

Bit

Description

0-2

3

4

5

8-15

Baudrate
0: 

    9600

1: 

  14400

2: 

  19200

3: 

  38400

4: 

  56000

5: 

  57600

6: 115200
7: Reserved
0: Odd 

parity

1: Even 

parity

0: Parity 

disabled

1: Parity 

enabled

0: 

1 Stop bit

1: 

2 Stop bits

Response delay [ms] (5..255)

Resetting of communication settings

Once the MODBUS settings have been stored in the device, communication with the device is only possible if the settings 
are known.

The following technique resets the MODBUS settings to the delivery status:

- Device address: 01h
- Baudrate: 

19200

- Parity:   

None

- Stop bits: 

2

A plug prepared for this purpose (Te is connected to Terminal GND with a resistance of 1 kOhm) is connected to the 
RS485 interface before the device is switched on.

After the device has been switched on, the red LED shines for approx. 30 seconds. During this time, the green LED fl ashes. 
Subsequently, the red LED turns off (the green LED continues fl ashing). Within further 30 seconds, this plug has to be removed 
from the device.

After the successful completion of this procedure, the communication default settings are stored again in the device.

If the procedure described is not adhered to, the interface parameters are not changed.

Summary of Contents for SINEAX V604s




















Reviews: