16
Operating instructions V604s Be
Camille Bauer
Limitations of confi guration parameters
Options to combine types of measurement
Register: 40523, 40534
The numerous types of measurement can be combined with
each other in different ways.
See Table 3 page 19
The "earthed" combination is used if both sensors are
connected to each other.
Measuring ranges
Register: 40524, 40535
see table 1 / page 4
Address
Description
Data type
#
Default
Description
40580
OUTSET2
UINT16
05h,
at VB604s
01h
Output settings Output 2 (same as Output 1)
40581
OUTRANGE2
REAL
Output range Output 2
0
4.0
Minimum value
–20…20 [mA] / –10…10 [V]
1
20.0
Maximum value
–20…20 [mA] / –10…10 [V]
40585
TRIM2
REAL
Output trimming Output 2
0
0.0
Offset trimming
[in % of the output range, setting range +/– 10%]
1
1
100.0
Gain trimming
[in % of the output range, setting range 90…110%]
1
40589
ERRVAL2
REAL
0.0
Output value Output 2 in case of a fault
[in % of the output range, setting range -10…+110%)
1
40591
GRAD_TIME
REAL
1.0
Time span between two measured values for gradient calculation of limit values in seconds
Range: 4 x TSET … 26210 s
Automatic parameter correction
2
40593
NUMTAB
UINT8
Number of table values
0
0
Number of table values Table 1
Automatic parameter correction
2
1
0
Number of table values Table 2
Automatic parameter correction
2
40594
TAB1_YA
REAL
-10.0
Table 1: Y-value (-10%) in % of the measuring range
40596
TAB1_X
REAL[20]
0.0
Table 1: X-values in % of the measuring range
40636
TAB1_Y
REAL[20]
0.0
Table 1: Y-values in % of the measuring range
40676
TAB1_YE
REAL
110.0
Table 1: Y-value (110%) in % of the measuring range
40678
TAB2_YA
REAL
-10.0
Tabelle 1: Y-Wert (-10%) in % vom Messbereich
40680
TAB2_X
REAL[20]
0.0
Tabelle 1: X-Werte in % vom Messbereich
40720
TAB2_Y
REAL[20]
0.0
Tabelle 1: Y-Werte in % vom Messbereich
40760
TAB2_YE
REAL
110.0
Tabelle 1: Y-Wert (110%) in % vom Messbereich
1
Max. +/-22 mA or +/-11 V
2
Automatic correction of parameters in the device.
Each parameter must range within permitted limits. These partly depend on other parameters.
If parameters determining the limits of dependent parameters are changed,
(e.g. measuring range is dependent on the type of measurement), the respective parameters are automatically limited to the permitted parameters. The status will show that such a
correction has taken place.
Due to linking and scaling, the measuring ranges are rescaled
to different ranges.
This is automatically realised in the device.
Abbreviations:
k
1
: SCALE1
k
2
: SCALE2
T
1a
…T
1e
INPRANGE1
Min1 = T
1a
* k
1
Max1 = T
1e
* k
1
T
2a
…T
2e
INPRANGE2
Min2 = T
2a
* k
2
Max2 = T
2e
* k
2
Matrix
Minimum value
MEAS1
Maximum value
MEAS1
Input 1
Min1
Max1
Input 2
Min2
Max2
Input 1 + 2
Min1 + Min2
Max1 + Max2
Input 1 - 2
Min1 – Max2
Max1 – Min2
Input 2 - 1
Min2 – Max1
Max2 – Min1