manualshive.com logo in svg

Cameron Scanner 2000 microEFM, Hardware User Manual

Introducing the Cameron Scanner 2000 microEFM - the ultimate hardware user manual! Experience seamless navigation and troubleshooting with this comprehensive guide. Download the manual for free from manualshive.com, ensuring quick access to all the information you need for optimal product usage.

Share
Download
background image

B-1

Scanner

®

 2000 microEFM 

 Appendix B

Appendix B—Lithium Battery Information

Lithium Battery Disposal 

Once a lithium battery is removed from a device and/or is destined for disposal, it is classified as solid waste 

under EPA guidelines. Depleted lithium batteries are also considered to be hazardous waste because they meet 

the definition of Reactivity, as per 40 CFR 261.23(a)(2), (3) and (5). This document describes how the lithium 

reacts violently with water, forms potentially explosive mixtures with water, and when exposed to certain pH 

conditions, generates toxic cyanide or sulfide gases.

Federal law requires that depleted lithium battery packs be sent to a fully permitted Treatment, Storage and 

Disposal Facility (TSDF) or to a permitted recycling/reclamation facility. 

Important   Do not ship lithium battery packs to Cameron’s Measurement Systems Division.  

Cameron facilities are not permitted recycling/ reclamation facilities.

CAUTION   Profiling and waste characterization procedures must be followed prior to shipping a 

lithium battery to a disposal site. It is the shipper’s responsibility to comply with all ap-

plicable federal transportation regulations (see below).

Transportation Information

!

  WARNING: The Scanner 2000 microEFM contains lithium batteries. The internal component 

(thionyl chloride) is hazardous under the criteria of the Federal OHSA Hazard Communica-

tion Standard 29 CFR 1920.1200. Before shipping a lithium battery or equipment containing a 

lithium battery, verify that the packaging and labeling conforms with the latest version of all 

applicable regulations.

The transport of the lithium batteries is regulated by the United Nations, “Model Regulations on Transport of 

Dangerous Goods,” (special provisions 188, 230, and 310), latest revision.
Within the US the lithium batteries and cells are subject to shipping requirements under Part 49 of the Code 

of Federal Regulations (49 CFR, Parts 171, 172, 173, and 175) of the US Hazardous Materials Regulations 

(HMR), latest revision.
Shipping of lithium batteries in aircraft is regulated by the International Civil Aviation Organization (ICAO) 

and the International Air Transport Association (IATA) requirements in Special Provisions A45, A88 and A99, 

latest revision.
Shipping of lithium batteries on sea is regulated the International Maritime Dangerous Goods (IMDG) 

requirements in special provisions 188, 230 and 310, latest revision.
Shipping of lithium batteries on road and rail is regulated by requirements in special provisions 188, 230 and 

310, latest revision.

Material Safety Data Sheet

For a link to the current MSDS for the lithium batteries used to power the Scanner 2000 microEFM, see the 

Measurement Systems Division section of the Cameron website: www.c-a-m.com.

Summary of Contents for Scanner 2000 microEFM































































































































































































Reviews:

No comments

Related manuals for Scanner 2000 microEFM

Taber 5135 Operating Instructions Manual preview
5135
Brand: Taber Pages: 53
Keithley 236 Applications Manual preview
236
Brand: Keithley Pages: 201
E Instruments E4500 Operating & Maintenance Manual preview
E4500
Brand: E Instruments Pages: 144
Didactum Monitoring System 500 II DC Quick Start Manual preview
Monitoring System 500 II DC
Brand: Didactum Pages: 2
Magene P325 CS Quick Start Manual preview
P325 CS
Brand: Magene Pages: 80
Guru Home Systems GU-HB-201-R1 Installation Manual preview
GU-HB-201-R1
Brand: Guru Home Systems Pages: 20
Armstrong Monitoring Corporation AMC-CD2 Instruction Manual preview
AMC-CD2
Brand: Armstrong Monitoring Corporation Pages: 12
Veeco Dektak 150 User Manual preview
Dektak 150
Brand: Veeco Pages: 349
GrainPro GPO2-AN Instruction Manual preview
GPO2-AN
Brand: GrainPro Pages: 7
Caen DT5740 Technical Information Manual preview
DT5740
Brand: Caen Pages: 50
Reed Instruments R3525 Instruction Manual preview
R3525
Brand: Reed Instruments Pages: 14
Interacoustics AT235 Service Manual preview
AT235
Brand: Interacoustics Pages: 54
PCB Piezotronics 3501A2020KG Installation And Operating Manual preview
3501A2020KG
Brand: PCB Piezotronics Pages: 10
MULTISPAN AMP-23 Operating Manual preview
AMP-23
Brand: MULTISPAN Pages: 4
Racelogic RLACS277RLACS29 Quick Start Manual preview
RLACS277RLACS29
Brand: Racelogic Pages: 10
A&D AD-4530 Instruction Manual preview
AD-4530
Brand: A&D Pages: 2
Rinstrum M4201 Quick Start Manual preview
M4201
Brand: Rinstrum Pages: 2
Velleman DVM401 Manual preview
DVM401
Brand: Velleman Pages: 18

Brands by name

Popular brands

Load more brands