background image

AFTER INSTALLATION

CM9-2 INSTALL ATION AND OWNER MANUAL  V.3.1 | 2023.06.01

PAGE 25

Accessories 

- Additional accessories such as keypads, exit loops, and access controllers can be purchased

and installed to your gate operator. Ask your dealer or distributor for more information or visit our website 
https://calimetco.com and click on ACCESSORIES tab to view all available accessories.

Warranty 

- Register your warranty using the warranty card included in the box. This will require the serial

number of the gate operator which is located underneath the black cover, outside the circuit board compart-
ment. After you are done, mail in your warranty to the address specific on the card. Additionally, you may 
register your warranty online by visiting https://calimetco.com/warranty.

*NOTICE IF YOU FAIL TO REGISTER WITHIN 30 DAYS OF INSTALLED DATE. YOUR WARRANTY WILL
ONLY VALID FOR 1 YEAR WARRANTY.

Auto-Close Timer 

-

 

Most homeowners prefer the gate to close automatically after they drive through it. See

the “Dip Switch Features” Page, specifically the number 2 “TIMER” section to set up the auto-close timer on
your gate operator.

Dual-Gate Installation

 - For double gates, visit the “Dual Gate Setup” page for more installation instructions.

Homelink / Car Setup 

-

 

Most modern cars come with a feature called Homelink that lets you open your 

gate by pressing a button on your car. Calimet gate operators are compatible with Homelink. Visit the link: 
homelink.com/program/vehicle and enter your car model to view specific instructions. For order cars, or cars
with software that isn’t Homelink, check your car’s manual for setup instructions.

Safety

 - Read this instruction manual to learn the common features of a gate operator and their functions. 

Learn how to turn off the power and how to use the emergency key/lock release in cases of a power outage. 
Keep your gate maintained by following the “MAINTENANCE” page instructions.
Read the “SAFETY” page to learn the dangers of a moving gate. Educate all individuals on the property of
the dangers of a moving gate. Keep all children away from moving gates. DO NOT allow children to play on
or near the gate or operate the remote control.

Installers

 - Fill out the “NOTES” page with the gate operator model and serial number and provide them 

with your contact information. Leave instruction manual and product literature with the owner or end user.

Summary of Contents for CM9-2









































Reviews: