background image

MANUFACTURER’S LIMITED WARRANTY

CM9-2 INSTALL ATION AND OWNER MANUAL  V.3.1 | 2023.06.01

PAGE 36

The warrantor, CALIMET CO., INC, warrants the gate operator(s) for a period of three (3) years in commer-
cial installations and for a period of five (5) years in residential installation to be free from defects in mortor,
gearbox, circuitry, and workmanship. This warranty is limited to two (2) of any combination of repairs or 
replacement of parts. This warranty applies from the date of purchase to the original owner. Warrantor will 
repair or replace (at warrantor’s sole discretion) any part which it finds to require service, excepting that, this
limited warranty does not cover the following corrosion and, damage or failures resulting from environmental
conditions, vandalism, water, lack of proper maintaince, accident, theft, fire, normal wear and tear, misuse,
alteration, tampering, improper repair, installation of non CALIMET approved parts, accessories, or compo-
nents. 

This device must be send to the warrantor at the consumer’s expense 

to:

CALIMET CO., INC.
9949 HAYWARD WAY
SOUTH EL MONTE, CA 91733

The warrantor will return the repaired or replaced unit to the customer at the consumer’s expense.
The limited warranty does NOT cover labor fees for reinstalling a repaired or replaced unit or part.

These warranties are in lieu or all other warranties either expressed or implied, and CALIMET CO., INC.
shall not be liable for consequential damage. All implied warranties of merchantability and/or fitness for a
particular purpose are hearby disclaimed and excluded. This limitation is not valid in jurisdictions which do
not allow limitation of incidental or consequential damages or limitation of warranty periods. Please complete
the registration card and send it by mail within 30 days of purchasing from CALIMET, DEALER or your
INSTALLER. If not registered only a one (1) year warranty on all part will be provided.

The warranty card must be mailed to the address listed on the card with the proof of purchased (Invoice).
Alternatively, the warranty can be completed online at https://calimetco.com/warranty and email us your
proof of purchased (Invoice) with Email Subject: Full Name, Model #,  Serial #.

Summary of Contents for CM9-2









































Reviews: